JDB9910AWB Jenn-Air Dishwasher - Instructions

Placed it back together. Part select was right on time and used this companys site for yrs

did not even tell me that i had to order 2 packs of wheels with a little patients saw how to remove all 4 wheels to disassemble and re mount new parts Mounting bar replaced on r side is just carfully lined up and will come out of rack side and in reverse order carefully with out forcing replace 2 small V shaped parts must be lined up with their respective holes

Opened the box and put the new Silverware Basekt in the Dishwasher. Everything was atttached, no labor involved. Loved it, wish I had thought about ordering it earlier. Ordering, Receiving and Installing was EASY and QUICK. Thank You!

Removed the upper rack rail stops. Removed the upper rack by pulling outward until the rack rollers cleared the rails. Attached the new roller on the upper rack. You can look at the other undamaged rollers to see how they lock into place. re-install the upper rack by feeding the upper rack rollers back onto the rails. Install the rail stops back into the rail ends,and the job is complete. VERY EASY!

I had to call an appliance repairman to come fix it. If I would have been able to pull the dishwasher out, it would have been a simple fix. It would not come out and I loosened to water line trying therefore causing more problems.

I had to cut the old rack for 2 axles and add 2 wheels from the old rack to the new one that was sent. the new one had 2 less wheels.I used white zip ties and wheels from the old rack. Placing the wheels in the right place I used the zip ties to hold them in place. Without the extra wheels like the old rack had the new one would fall into the bottom of the dish washer. Working just fine so far.

Top holder was turning black and disintergrating. I orderder the part and the box arrived but I havem't had time to install it

ordered the basket and put it in its place.

I ordered the basket on Sunday and received it on Tuesday. It is a better basket than what originally came with the dishwasher. Very happy with the prompt delivery and service.

Both the handle and the screws that attach it to the dishwasher door had broken off. To replace the handle, unscrew all the screws holding the inside steel liner to the door. This takes a very small screwdriver or a screwdirver with a small star-shaped end. Do not pop the vent on the inside of the door. If you do, you will have to whack it hard to get it to seal again. With the screws broken off, you have to guess the replacement length. It worked with 1" #8. I think the thread count is 10/inch. Most of the time involved was finding the right tools, getting the right screws and replacing the vent, which I should not have removed in the first place.

Extremely easy to repair. I can't believe I didn't do this earlier.

I Googled parts for an Electrolux wheel and Parts Select came out with a picture that confirms the one that I need. The price of the item was very reasonable as compared to the official website of the manufacturer. I like what I saw and bougt 4pcs instead. I will recommend Part Select to my friends without hesitation.

replaced mounting strip and two wheels

I found a short video on YouTube that showed me how easy it was to remove the old dishrack and install the new one. I would have never figured out how to get old diskrack out without watching short video clip. And, all I needed was my fingers to undo the end clips.

I took the suggestion of a previous reviewer to bend the new part in. But instead of using pliers to remove the old part, I tried bending it to get it out. This was so that I could see how much force would be necessary to bend it without breaking it to get the new part in. I bent it in the middle and was able to get it unhooked from one side without too much force. To get the new piece in, first I made sure I had it lined up correctly. Then I inserted the circle over one of the side prongs to hold it and gently but firmly bent the piece in the middle until the circle on the other side could slip over the other prong. It was not bent enough to stay bent, just to compress it into the space and have it spring back to full length.