JDB6510AWP Jenn-Air Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Rust And Detioration Of Dishrack
I read the other persons who did the same job to find out how to remove and replace the tower on the lower rack. Then just lifted out the old one and replaced it with the new one after attaching tower and replacing silverware tray. I have ordered parts from parts select in the past, and have never had a problem. Thank you
Parts Used:
-
Marilyn from Nebraska City, NE
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Snap retainer broke.
-
Garth from krakow, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The upper spray arm kept falling off.
I replaced the spray arm snap retainer,but the problem still exists. Do you have any suggestions?
Parts Used:
-
MONA from HOUSTON, PA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Wheel broken
It's just a matter of snapping them on the tray ... what was a amazing was the delivery time. Fastest general delivery I've ever encountered on an Internet order ... I'd swear it was overnight (though it may have been a day more), but whatever ... it came standard shipping... great job all around ...
Parts Used:
-
Gary from Aquebogue, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The filter had become brittle and needed replacement.
removed the bottom rack and the lower spray arm. With a star point screw driver removed 6 screws to take off pump housing. Lifted out the old filter. carefully bent the new filter (shipped flat) into a circle and connected end clips. Replaced bottom edge of filter into groove. Replaced pump housing and spray arm. Back in business!
Parts Used:
-
Harry from Canyon Lake, TX
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Water leak do to freezeing, the solnoid cracked.
The part is on the bottom of the washer. You have to remove the front panel at bottom (four screws)The part is on the left side of the washer. First thing to do is to remove the water inlet hose, using an open end wrench. There are two screws that hold the part to the sideof the washer. I used a multibit screwdriver with no bits in it, it the right size and works very good. Disconnet the electic from the part. Turn part so you can the see outlet hose & clamp, use a pair of plyers to open and slide the clamp up the hose, and pull the hose off the part. To reassmble reverse the procedure.To show how easy this is I'am a 76 year old man and had no trouble at all. The hardest part of the job was finding the leak in the first place
Parts Used:
-
Robert from Morley, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
the handle had broken off - the wheel fell off
I followed the directions left by others - the wheel just snapped onto the rack - the handle was just as easy - unscrew all of the screws on the door, remove the broken handle parts and install the new handle. Very very easy repairs.
Parts Used:
-
Shirley from Bridgewater, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
SIlverware Basket broken - items falling thru
Easy- just ordered the new basket and swapped out the old one. the new one I received is sturdier and better made than the old one that the machine came with. I think I read somewhere the Maytag redesigned it because the original one did not hold up well. All repairs should be this easy!
Parts Used:
-
Cassi from Los Angeles, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
rusted lower rack
Removed rack but had trouble removing the tower and didn't find any help in your video...finally just twisted it out.
Parts Used:
-
Margaret from Bellingham, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Silverware basket was broken
-
Kelly from Hempstead, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Top rack rusting in several places. Broken tines
Removed the rack by unlocking the slide stops on each end. That was a bit of a chore until I figured how to remove the stops. Then fairly easy. Removed the 2 small pivoting side rack attachments from the old rack and installed them on the new rack. Installed the new rack in the two sliding side rails and the job was done.
Parts Used:
-
Armond from Placentia, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Original silverware basket developed holes in the bottom
Took out the old basket, put in the new one. It fit perfectly. Part arrived in record time.
Parts Used:
-
Darlene from Lenexa, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
There were holes in the bottom of the old silverware basket, which the handles of the silverware dropped through
I took out the old basket and dropped in the new one. No tools were needed. I am really glad that PartSelect carries this item because Maytag does not. Getting this part will allow us to get a few more years of use out of the dishwasher. The bottom of the old basket was disintegrating to the point where it would soon have become unusable and without the replacement basket, the dishwasher itself would not have been worth keeping.
Parts Used:
-
Mary from Avon Lake, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
original rack was damage
the replacement was easy, just have to pull the water jet out and attach to the new rack.
Parts Used:
-
Maria from Wanaque, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Did not spin and dishes dirty
First I took apart and went to local appliance store. The wash impeller was broke for sure, but I could not figure how it worked. Their diagrams were not accurate and they only sold a kit for $40 just to get the wash impeller. I went online and found your site. I also could tell by your diagram(which was accurate) that the discharge pump housing was broke also. I found this on your site since it was under the problem I was having. I ordered the parts from you for $32 with shipping (included wash impeller and discharge pump housing). I received the parts on the second day, watched the video, and put back together. It works excellent. I am very impressed and will use your site for anything that breaks, and tell everyone about it. Thanks
Parts Used:
-
William from Kirtland, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Socket set
Was this instruction helpful to you?
Thank you for voting!