Models > JDB3610AWX > Instructions

JDB3610AWX Jenn-Air Dishwasher - Instructions

All installation instructions for JDB3610AWX parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDB3610AWX
61-75 of 474
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking around the Inlet injector on side of dishwasher.

  • Customer: Juli from Grangeville ID
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
My original order was for the "Motor Gasket" in the bottom of the tub that just looked nasty. Not leaking. Replacing that was a little more complicated, but used another customer's recommendations and worked great. Ran an empty load to check for leaks and thats when we discovered that we had a leak on the side of the darn thing. So we ordered the "Injector Seal Ring. Got it in about 5 days and after installing, (2 seconds), we still had a leak! Soooo, ordered the "Water Inlet Injector". 5 days later, we have NO MORE LEAKS!!! I would STRONGLY suggest that anyone who has a leak at the Water Inlet, order a new Injector right along with the Seal Ring. The shipping and handling was WAY more than the price of the parts. I'm happy to say that my 10 year old dishwasher is running like a champ. Thank You.

Water leak from Bottom of Float Assembly

  • Customer: Michael from Cheshire CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 8 people found this instruction helpful
Remove the Palnut Screw from bottom of Float assembly using pliers, Remove Pivot pin from Actuator lever w/ screw driver. Replace the Float , install new palnut Screw and re-install pivot pin on actuator lever.

That's it !!!!!!!!!!!!!!!!

Not washing properly. No water shooting through the jets

  • Customer: Manfredo from Palm Beach Gardens FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 5 people found this instruction helpful
It takes about 5 min. to disassembled the lower jet system. As you disassemble, make sure you clean all the filters, and asses the integrity of the filters. If they are broken, you need to replace. Once you get to the impeller, you know it is broken because the lower part is loose. To replace you need to firmly hold the impeller as you unscrew the top screw. If the housing gasket is broken or too loose, replace. Otherwise you will have leak. Refer to your models diagram for proper assembly.

water leaking

  • Customer: Benjamin from Montrose CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 8 people found this instruction helpful
SIMPLY REMOVE THE WASHER NUT,THEN PULL THE FLOAT ASSEMBLY. AS FAR THE LEVER,JUST UNSCREW THE SCREW AND REPLACE THE ACTUATOR LEVER. WHAT WAS GREAT ABOUT EVERYTHING I WAS ABLE TO GO TO THE PRESENTED DIAGRAM. THIS ALLOWED ME TO FIND THE EXACT PARTS I NEEDED.OF COURSE MAKE SURE YOU HAVE THE MODEL NUMBER.

Water leaking out the right side bottom of door.

  • Customer: Thomas from Oneida NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 6 of 8 people found this instruction helpful
Very easy to do. Used needle nose pliers just to get a first grip on the door gasket and then pulled it completely out. Pulled up the Water Deflectors by hand. Cleaned the gasket trough with a soft cloth, warm water and dishwashing detergent. Rinsed. Then simply pushed the gasket into the trough, lightly tapping into place, then pushed on the water deflectors, and no more leak!

Noise when washing or draining

  • Customer: Daryl from Turlock CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 6 people found this instruction helpful
Remove bottom rack. Unscrew the retaining ring on the wash arm, remove along with wash nozzle. Unscrew the eight retaining screws on the filter cover and remove (be carefull not to lose the two plastic bushings). Pick off and set aside the wash fan. Remove the six retaining bolts on the discharge housing. Pull up and remove the discharge housing. Remove the gasket (buy a new one, cheap and easier) with small screwdriver. Push gasket into new assembly. Under plastic nut with pliers and take off the plastic bushing that the wash arm rides on. Install new housing assembly with the parts that was taken off in the reverse order. Be carfull when installing the filter cover to make sure the drain outlet is aligned or mated to drain. Gently push down until the filter in down and continue reassembly.


(PS: Never use Sears parts, they extrembly slow as well unable to deliver on time).
Wash your dishes

Leaks out and below the front door

  • Customer: John Todd from Franklin WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 9 people found this instruction helpful
First of all, rather then spending the 44 dollars on the main door seal simply cut yours in halve and trim a quarter of an inch from the disintegrated ends and use superglue and glue these ends together. this glued end will now be up top and in the middle and new clean ends will be down in the corners. next I removed the plastic door panel using a torxhead screwdriver, I just stuck the new inner foam pad on the old one. Then I glued rubber washers to the inner frame about 1/8 thick in the top 2 corners only. Finally I reattached the plastic door being careful not to tighten the torx head bolts just tight enough. It's dry and working good.

Leak around door

  • Customer: RON from MOUNT AIRY MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 4 of 4 people found this instruction helpful
Removed old door gasket and water deflectors and replaced with new. Got the gasket in backwards at first. Removed and rotated 180 degrees and it went in properly. (Used tech video provided by parts select to help me.)

Though the old gasket was definitely bad, water still leaked after replacement.

Key issue ...... over time, contamination has accumulated in the water shutoff lever assembly and also on the shutoff microswitch underneath the internal water float, making both sticky and non-responsive to water level. Water had been overfilling. (probably defaulting to a maximum number of seconds to fill). ALSO - original installation was not totally level, with back of tub higher than the front.

Leveled tub. Removed mocroswitch and lever and cleaned both of sticky grease.

No more leakage.. basic problem was actually overfilling, allowing water to surge into the lower internal door vent upon pump startup.

Ron
Mount Airy, MD

No Water caused soap to not dispense & no clean dishes.

  • Customer: Robert from Brookdale CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 4 of 4 people found this instruction helpful
I took off the front bottom panel for an easy access. The valve is located on the left. Shut off water to the dishwasher. Remove the bracket that holds the valve. Remove hoses and 2 wires on the valve switch. Install new valve by revesing the steps above.

water not flowing into dishwasher

  • Customer: Doug from Cornish ME
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 5 of 7 people found this instruction helpful
turn off breaker
turn off water supply line
note wire color locations on notepad
disconnect 2 spade lugs (pliers)
disconnect inlet line (adj. wrench)
disconnect outlet line (pliers on hose clamp)
remove old valve assembly (4 screws w/nutdriver)
remove ground jumper from old valve
remove inlet pipe ell from old unit (vise & pliers)
clean open end of pipe ell (file)
apply teflon dope tape to pipe threads
install pipe ell on new valve
reorient solenoid 90degrees cw to match Maytag installation
reinstall ground jumper
install new valve assembly in dishwasher
reconnect hose and hose clamp
reconnect inlet line
reconnect spade lugs
turn on supply line, check for leaks
turn on breaker
start washer at appropriate cycle to test water flow
done!

my silverware basket was broken

  • Customer: donna from houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
I reviewed the choices available, found what I needed, ordered it, got it (quickly), and dropped it into the dishwasher....happy happy!

Dishwasher not getting dishes clean

  • Customer: Matt from Middletown MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 4 of 4 people found this instruction helpful
Piece of cake. I panicked for a minute before I realized that there was a threaded brass 90 in the inlet valve. It looked like it was the wrong part for a minute. Once I got the 90 reinstalled in the new valve, I had it back together in 10 minutes. It seems to be working better.

Door leak and leak on inlet valve

  • Customer: April from Valdosta GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 4 of 4 people found this instruction helpful
I replaced the door latch grommet just as everyone else has described on this site. It was pretty easy. I was amazed that such a little piece of rubber can let so much water get by. The inlet valve was not too bad either. Take the two bolts out that hold the bracket to the dishwasher. Remove the rubber hose on the back side and take loose the two electrical connections. My water line was long enough to pull it out in front of the dishwasher. Then I took the water line loose and removed the fitting. Installed the new one in reverse order of what I just described. These items took care of the bulk of the leaking problem. But I am in the process of ordering a new door seal which I hope resolves the rest of the issue. Also make sure you check the upper and lower control arms to make sure the spray holes are free of debris. This dishwasher was full of pieces of clear plastic that caused the spray arms to spray indirectly and towards the cracks of the doors.

leaking door- Dispenser Door Latch Grommet

  • Customer: Peter from San Jose CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
Myscanning other reviews i saw mention dishwahser developed a small leak on RHS of door. I assumed the door gasket and planned to order that. On of the dispenser gromet which is only a $5 part so ordered that as well. I first replaced the door gasket which is an easy 10 mins job and ran the dishwasher again, but it still leaked.

I then removed the 7 torx screws on the door panel which came away easily. It was obvious that water was in there, so i removed the two screw on the dispenser with a nutdriver to replace the grommet. This process took 20-30 mins. After reassembly the leak was gone.

Without the comments on the website i would never have thought of the disepenser as source of the problem.

dishwasher door leaking

  • Customer: JoAnn from Raleigh NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
I removed the old door gasket and thoroughly cleaned the track. I placed the new door gasket in place- no problems.
I had to remove the 7 screws from around the door to access the old, crumbled gasket. This was accessed by removing 2 screws with a socket wrench. The old gasket pulled out and the new one slipped right in.
No more leaks!
All Instructions for the JDB3610AWX
61-75 of 474