Models > JDB3610AWX > Instructions

JDB3610AWX Jenn-Air Dishwasher - Instructions

All installation instructions for JDB3610AWX parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDB3610AWX
46-60 of 465
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lots of noise and wouldn't pump

  • Customer: Joe from Franklin NC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 6 of 6 people found this instruction helpful
I first removed the washer arm. Be careful because it is screwed on with the large center plastic piece with right hand thread. That allowed me to take the arm and disc off.

Next I took 6 screws loose with the allen wrench. This allowed me to get to the filter ring. I removed it and that allowed me to get to the three screws holding the discharge. I used a 5/16th socket to remove them.

A plastic disc that was part of the upper pump came loose and caused the noise. I replaced the upper discharge housing (with upper pump as part of it) and upper discharge housing gasket and reversed the order to reassemble.

The exploded diagram was a terrific help

Leaks on floor in front of washer.

  • Customer: Jim from Yorba Linda CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
Removed two lower panels using nutdriver. Ran washer through a rinse cycle, to determine for sure where leak was coming from (under door on left). Examined the door gasket and observed buildup of lime deposits and a general depression of the gasket through years of use, especially in lower portions. Removed the old gasket observing how installed. Cleaned out groove with Lime-away and toothbrush. Washed clean using water in a squirt bottle. Dried things out using paper towels, and then pressed new gasket into place, starting at lower left. Readjusted the gasket to fit precisely end to end. Shut door and ran a drip free load.

I accientally busted the old rinse arm, while I was trying to put in the filterguard with bottom spray arm jet

  • Customer: mary from sturgis MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 6 of 6 people found this instruction helpful
I took the bottom rack out of the dishwasher. I then took the filter guard and bottom spray arm out. Then I took the screws out of the filter guard to get to the rinse arm. I took the filter guard off, took the old rinse arm out and put in the new one. Have to make sure it is completely resting inside there. Then I put the filter guard back on. Put the screws back into the filter guard, put the two arm seals down around the rinse arm, put the bottom arm spray with guard back into the notches, put the screw top on so it can screw back in and the dishwasher is ready to go. Just make sure that you don't have a lot of soap built up, it will not clean the dishes right nor will the spray arms move. I had to call my appliance person out, and I have so much built up from soap, that I had to order a new filter guard and top and bottom spray jets. I now know to switch back to powder or liquid soap, because the tablets make a huge built up of soap... I have these parts on order now. In the meantime, I am cleaning out the jets with dishwasher magic and vinegar while I am waiting for my new parts. I now know how to put things back together so when I have this happen again I will know how to do it to save me the 63.00 office call and parts. I am happy that I know where to get my parts when I need them or break them by accident on trying to put my dishwasher back together again. Thanks.

Water leaking around the Inlet injector on side of dishwasher.

  • Customer: Juli from Grangeville ID
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
My original order was for the "Motor Gasket" in the bottom of the tub that just looked nasty. Not leaking. Replacing that was a little more complicated, but used another customer's recommendations and worked great. Ran an empty load to check for leaks and thats when we discovered that we had a leak on the side of the darn thing. So we ordered the "Injector Seal Ring. Got it in about 5 days and after installing, (2 seconds), we still had a leak! Soooo, ordered the "Water Inlet Injector". 5 days later, we have NO MORE LEAKS!!! I would STRONGLY suggest that anyone who has a leak at the Water Inlet, order a new Injector right along with the Seal Ring. The shipping and handling was WAY more than the price of the parts. I'm happy to say that my 10 year old dishwasher is running like a champ. Thank You.

Not washing properly. No water shooting through the jets

  • Customer: Manfredo from Palm Beach Gardens FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 5 people found this instruction helpful
It takes about 5 min. to disassembled the lower jet system. As you disassemble, make sure you clean all the filters, and asses the integrity of the filters. If they are broken, you need to replace. Once you get to the impeller, you know it is broken because the lower part is loose. To replace you need to firmly hold the impeller as you unscrew the top screw. If the housing gasket is broken or too loose, replace. Otherwise you will have leak. Refer to your models diagram for proper assembly.

Leaking lower inner door foam seal. Float leaking

  • Customer: Ronald from Seekonk MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 8 people found this instruction helpful
Make sure dishwasher is powered off. Remove all inner door panel screws. Lift inner door panel upward and lean against the tub. Use a putty knife or spatula to lift old lower foam seal. Make sure door seal area is clean. Start at one end, butt new foam against the side of door and slowly pull glue strip backing while pressing foam down from left to right. Reverse door assembly.

Make sure dishwasher if off and door unlatched. Remove lower kick panel 4 screws and remove 1 screw securing float switch arm. Hold float stem with pliers and remove bottom stem nut. Remove float and re-install the new float with reverse procedure listed.
Super fast shipping on items!! Great service.

Front door panel had scratches and dents from the wheelchair.

  • Customer: Nga from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
Front Door Panel was replaced by unscrewing 3 screws on each left and right side of the dishwasher.

The bottom screws did not need to be completely unscrewed, just losen it enough to be able to remove the panel out.

Replace it with the new panel and screw back in the screws.

Neither the Soap or Wax dispensors worked for years and there was water leaking from the front of the machine.

  • Customer: JOHN from PALM BAY FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
Actual i missed diagnosed the leak and ordered a very expensive door gasket. The leak was coming from shrinage of the wax resevoire o rig and the tab seal for the soap dispensor. I missed the trees the forest got in the way. The leak was dripping alond the front panel well away from the main door seal.

I cleans a the plastic surfaces and noticed a lip around the opening for the reservoire and used 150 sandpaper to remove it. Replaced the O ring, tab seal and bothe selonoids and cleaned everything. Put it back together. Works find lasts along time

Replace lower dish rack as orignal was corroded and the holders were rotted

  • Customer: Geoffrey from Shrewsbury MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
Took the replacment rack out of the box and found that it was the proper one. Had to rotate out the water director tower from the orignal rack and install it in new rack which took a few seconds to figure out . it was time to discard the ailing rack! Apparently the dish soap can attack the rack materia if there is any metal exposed and rot it out like rust so when this happens time for a new one. Otherwise there are no pins to support the bowls and plates in the lower section.

Approx 24"W x 18" H front door panel was dented.

  • Customer: MICHAEL from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
Remove three phillip's head screws from the right- and left-side trim strips. Bow panel slightly to remove. Reverse steps to reinstall. Very easy repair.

Tub was mysteriously slowly filling with water.

  • Customer: Mark from Austin TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 5 of 5 people found this instruction helpful
Figured out that the only thing that could be causing this was a bad inlet valve. Repair was really easy. Didn't even have to pull machine out from under cabinet. First removed kick plate. Then placed towel under the old valve. Undid the power connections and water lines (in and out). removed the to screws holding the valve to the body of the washer. With the valve free, removed the brass elbow and installed it on the new valve. Reinstalled the valve and all connections. Works like a charm.

The detergent cup cover would not open and the rinse aid was not dispensing properly

  • Customer: Timothy from Northville MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
I removed the seven screws from the back panel of the door (special tool) and seperated the back panel from the front. My wife held the back up and I removed the two wax motors (detergent cup and rinse aid), which were clipped in place. I had turned off power to the dishwasher, so I simply unplugged each wax motor from the wiring harness, plugged the wax motors in and clipped them in place, making sure that the wiring harness was put back in the same place. Then I put the back panel back on the door, turned the power on and tested the repair. The dishwasher worked perfectly. Thanks to PartSelect for helping me solve the problem. The parts arrived in two days!

Noise when washing or draining

  • Customer: Daryl from Turlock CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 6 people found this instruction helpful
Remove bottom rack. Unscrew the retaining ring on the wash arm, remove along with wash nozzle. Unscrew the eight retaining screws on the filter cover and remove (be carefull not to lose the two plastic bushings). Pick off and set aside the wash fan. Remove the six retaining bolts on the discharge housing. Pull up and remove the discharge housing. Remove the gasket (buy a new one, cheap and easier) with small screwdriver. Push gasket into new assembly. Under plastic nut with pliers and take off the plastic bushing that the wash arm rides on. Install new housing assembly with the parts that was taken off in the reverse order. Be carfull when installing the filter cover to make sure the drain outlet is aligned or mated to drain. Gently push down until the filter in down and continue reassembly.


(PS: Never use Sears parts, they extrembly slow as well unable to deliver on time).
Wash your dishes

water leaked through front vent

  • Customer: mark from ardmore OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Peeled off the old foam strip, cleaned with rubbing alcohol, let dry completely, applied new foam strip,replaced door interior done I wish repairing relationships with fiance and kids were one tenth this easy.

Water leak from the dishwasher door

  • Customer: Michael from Bronx NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
After replacing the door gasket and seeing that this wasn't the problem, using the schematics found at partselect.com I finally realized that it may be the insulation foam strip. I ordered the product and received it very quickly. Installation went fairly quickly. It was easy to remove the old foam strip and install the new one. The only problem was that the foam strip was about 1/4 " too short and it didn't cover the entire bottom. I improvised a little bit and cut off some of the old strip and covered the gap. So far the leak seems to have been fixed. In addition to the foam strip I had to buy a torx screwdriver for $11 at the local hardware store. The total spent was around $25.
All Instructions for the JDB3610AWX
46-60 of 465