JDB1100AWS Jenn-Air Dishwasher - Instructions

out with the old in with the new

Removed the dishwasher from under the counter. Turned dishwasher on side. Placed new drain pump from Parts Select into position. Replaced and tightened screws on drain pump. Reconnected hosing and electric. Stood dishwasher back up. Placed dishwasher back under counter. Turned on electric to dishwasher. Checked to see if dishwasher powered up. Turned on water supply valve to dishwasher. Set screws to hold dishwasher in place under counter. Loaded dishwasher with a few dishes and washed them. Worked perfectly. Parts were easy to find on Parts Select. Delivery was very fast.

I simply removed old lower dishrack from dishwasher and discarded. Then I removed new lower dishrack from box and installed it into dishwasher, no tools necessary. How easy is that?! New lower dishrack is a perfect replacement and now our dishwasher is good to go. Thank you PartSelect for your fast service.

replaced basket with a new one, so easy even a cave man could do it.....i think.......

The original problem that brought me to Parts select was a broken wheel on the top tray. While searching for part #s I came across several descriptions of dishes not clean . The videos available on line here were very detailed. This encouraged me to go ahead and order the parts. They arrived soon and were accurate to my order. The video on replacing the seal and chopper walked me through the entire job very clearly. Going slow and carefully keeping track of al screws I replaced the chopper, impeller and the filter. The filter did have a tear in the screening which allowed dirty water back up into the dishwasher.

I put the new one in and that was all

Pulled the dishwasher out from the counter. Wiring and supply hose were long enough that I did not need to disconnect them. Suspected a leak in the injector hose but the evidence was circumstantial. That is mineral deposits collected around the area where the house connects to a small plastic box and then into the dishwasher. I replaced the hose in a few minutes and added a clamp on the box side where no clamp was called for. So far, no leaks.

No repair, just an replacement. Would recommend this company for good service.

The docking stations just pulled of and snapped on. I took the tube in the back out to make sure the docking stations were seated well but I'm not even sure that was needed. Very easy. Another contributing factor was using rinse aid with an all-in-one gel pack detergent. I let the rinse aid run out and it's been working great ever since.

Removed dishwasher unplugged heating element wires unscrewed nuts removed old element replaced with new one. Tightened nuts snapped wire connecters back reset dishwasher ran quick cycle hot steam and dry dishes.Thanks Joe (saved me 1,500 for a new one)

Took old one out and put new one in.

We recently purchased a new home and it didn't matter how hot we ran the water in the sink before starting the dishwasher, the dishes, especially glasses, were filthy. Extra rinse cycles, pots and pans cycle, nothing worked. After finding this site, we took the chance on what the troubleshooter recommended and bought the accumulator filter and wash impeller. The parts came so fast! We followed the videos on this site step by step and we were successfully able to replace the filter and impeller. The impeller was COATED in nasty slimy grossness; it was obvious the previous owners never rinsed their dishes before running the dishwasher. After replacing these two parts, we have clean dishes! We have switched from tablets to liquid detergent which also helped (not sure why, tablets have worked at our old house just fine).

I removed the end caps by push the plastic tab on the end towards the top rack and pulling end cap towards me as I was facing the front of the dishwasher. I then removed the rack from the sliding track. Rotated the locking clip on the roller that clips on the rack's bar and slid the roller off the axel. Slipped the new roller on to the axel rotated the roller to the locked position. I then placed the rack back on the sliding track slipped the end caps back on and done. Very easy no tools required.

Remove and replace a washer impeller. Simple

the repair took all of 5 minutes; the wheels snapped on very easily.