JCD2389GES Jenn-Air Refrigerator - Instructions

removed old ice maker by taking out a couple of screws in the back of freezer,when new ice maker arrived i saw that it didn't have the same hose apparatus as old one so I easily took apart old one then took apart new one and switched them out-very-- easily done for a 61 yr old lady I might add-- also had to reinstall ice maker arm off old ice maker as new one does not come with one Then installed new ice maker in freezer I am very very pleased,sure saved a lot of money doing it my self

No tool required! Pulled out tray, emptied ice into large bowl for reuse. Pushed in and pulled from inside the coil springed auger until could get old plastic ring off and put new one on. Useing care not to apply too much pressure to ice dispensing end so as not to break housing. Have to turn auger assembly at an angle to compress enough and get old ring off. Needs a little physical strenth & care not to force plastic housing to breaking point. Worked great reused saved ice. Took less than 10 minutes

Maytag wide by side refrigerators tend to eat these parts about once a year, and this is my third assy so the replacement went very fast. When we used the Maytag warranty they replaced this part about 6 times, after they exchanged the refrigerator. No major disassembly is required, drop the plastic after removing a few screws, plug in the assy, and you are good to go, no more frozen food in the refer. The only tricky part is getting the clips to release so you can slide the plastic cover forward, but after a while they break off and it is easier to remove.

Used the flat head screw driver for leveage to pop the door off. Replaced the chill door by placing at an angle and snapping it into place. Works perfectly!

Very easy to order from parts select. Took seconds to replace.

removed the front panel on freezer door ,removed and disconnected panel ,removed panel containing solenoid,replaced with new solenoid. replaced all parts. works perfect..

I turned off the fridge. Used a nut driver to remove panel and defrosted coils with a hair dryer. Undid the old assembly and plugged in the new one, put panel back on and turned fridge back on. I have replaced the Adaptive Defrost Timer and the Defrost Heater and Thermostat Assembly.

I could not find the part online because the description did not match the owners manual for the refrigerator. I called the 800 number and decribed what I was looking to replace. They found the part immediately, gave me the part number and then I ordered it online. The part arrived sooner than expected and was wrapped in protective paper as the part was very fragile with a small circuit board on the back. The repair was easier than I thought and saved me nearly $500 in a service call and installation. Thank You - the refrigerator is as good as new.

First we removed screws in the top hinge, then lifted the door up and off the bottom hinge. Replacement of the door closer and lower hinge pin took less than a couple of minutes. Then putting the door back on and screwing the top back on was nothing.

We additionally replaced the puriclean filter which simply was twisting it off and then the new one back on

I used a nutdriver to unscrew the four bold, I disconnect the defrost heater assembly, I used boil water to unfreeze where the heater assembly hook, then I unclip the bottom I remove it and slide the new one the same way and replaace those two covers and connect the fridge back and it work like a charm. Thanks again Partselect. I save a bundle money and waiting time....

I took out the bottom two food baskets and one shelf. Removed two screws with a 1/4" nut driver. Then took two screws of the cooling element of which the defrost element was attached underneath. Disconnected two plugs and replaced the new part. The easiest repair I have ever done.

I took off the backing off the back of the refrig. & the water valve with a nutdriver. Then unpluged two wire connectors & disconnect three water lines. Pulled out the old valve & hooked-up the new valve in reverse order. It don't get any easer than that. The dripping water dispencer was no more.

First off, We have an extended warranty however, they said it was not coverered since it did not affect the function of the refrigerator (except that we lost refrigerator space and could no longer use that section of the fridge!!!) They said it was cosmetic!! After having a repair person come out and tell for the part and repair it would be $217.00.
I then got on line and looked up the part which with shipping cost us 37.00. My husband installed the part in no time.
Word of advice: make sure when you purchase warranties that you check the fine print ,because there are all different levels of warranty.

I ordered new solenoid that came with door. I installed it and it was making a very loud buzzing noise. I also had a frost buildup between the icemaker and the icemaker chute in the door. I posted my problem on the forum and Sheila suggested that the heat from the defective solenoid might have distorted the fountain housing, causing the new solenoid not to seat right, and possibly letting outside air into the icemaker. On closer inspection I saw that the hosing WAS distorted. I ordered a new one, installed it, problem solved! Hats off to the staff here, where else can you get a diagnosis first -so you know what parts to order!

I removed the cover and unplugged the heater unit and thermostat. I then checked the resistance of the unit. The unit was bad. I then replaced the unit.
This was a very simple repair.