HLSR1090J7WW Hotpoint Washer - Instructions

Just traded out the hoses and installed washer and started washing. Also got the replacement hose in a very timely manner, in turn only without washer for 5 days total. Thank You

just like the video showed/////only idid not kno the water would escape from one of the hoses when removed///video did not prepare me for this

I took the two screws out that was holding the bracket and hose in place. I then pulled the hose out and then had a little bit of a hard time taking off the bracket (it was plastic and felt if I bent it to hard it would break) wiggling it down to the end of the hose. Re inserted the hose attached bracket, and I was done.
It would have cost me a lot more then $20.00 to have a repair man come in and fix it.
Love the service, delivered in two days.
Will use them again.

Pulled off front cover of machine. Unplugged unit. Used a channel lock (water pump pliers) to squeeze the hose clamp on the suction hose. Pulled hose off of pump suction. Did same for discharge hose. Some standing water came out onto floor of unit. Unscrewed 2 screws from base using nut driver. Pulled the 2 wires off of the stabs of pump. Re-installed new pump in reverse order. Unit back on line in 15 minutes, and works fine.

First i removed the bottom of washer and removed clamps from two hoses connected to the pump , removed 2 pump bolts along with wire connector. Then reinstalled new pump, hoses and wiring and that was it. Very easy !

R & R drain hose

The staff at parts Select are one of a kind, my order came before expected. Thanks Parts Select

The main issue was the Timer Dial was stripped, not allowing the selection of cycles. The Timer deck had already been dismantled. I had the parts ordered, ad the next day they were at my doorstep. It took 5 minutes to replace the necessary parts and get the washer back in action again. The parts were a bit pricey, but I suppose that beat having to purchase a new washer. Hopefully they last.

Lay the washer on its side, unscrew three screw to loose the rotor, put the belt and screw the rotor back.

Took 30 seconds after I recieved the part from you guys. $8 repair. Sweet!

This job did not take much longer than 15 minutes if that.1st take the cord or twine and loop it under 2 paddles of the agitator.( there is a small groove under each of the paddles that has enough space to put the cord in) Pull up on the cord to remove the agitator. 2nd. Under the agitator is a bolt that secures the agitator coupling. Remove that bolt. Keep bolt(you may want to replace this bolt if rusted and worn. Mine was still ok so I reused it.) 3rd pull up on Agitator coupling to remove. Teeth were worn on Coupling, So discard. 4th Insert new coupling, replace bolt to secure coupling. finally slide agitator back over coupling till locks back in place. ....Done.

had to put timer in and it was held by one screw and the timer knob was use a push on part with a clip that you had to use the needle nose for. And that was it all done and seems to run better than it did before.

We bought this used Hotpoint that was probably one of the original machine created back in the stone-age, it's so old. We've had it 10 months, and it's always had this... burnt rubber stink to it... then one day, it stopped agitating and sounded like a metal bucket of bolts being shaken. We're on a military income with five kids, and the idea of buying a new washer was just... heartbreaking. On a whim, having fixed a washer once before, we opened the front up and painstakingly pulled every last rubber fiber from what used to be the belt. Ordered the part. It shipped quick, arrived quick, and in under a week we were back in business. Someone else had mentioned the needing 1/4" socket, and I was glad I remembered that, because it made is SO much easier.

DISCONNECT POWER----1.- No pump sound when energized but I know it energized as the coil became a magnet. 2.- You need a drain pan to catch the water from the lower tub when the drain hose is disconnected from the pump. 3.- Water pump or channel lock pliers needed to remove the spring clamps on inlet and outlet from pump. 4.- Remove the 2 hold down bolts and the plug in power connection and the pump comes out very easily. 5.- On my pump I found a plastic tie wrap lodged in the pump impeller vanes-- this caused the pump either not to work at all or cause a cavitation effect caused the water in the tub not to drain completely. 6.- Since I had already purchased the new pump I installed the new pump and cleaned the old one to keep as a spare-- probably never going to need it though.7.- On the large diameter drain hose ( pump inlet ) I decided to use a auto hose clamp instead of the original spring clamp because the area to work on this pump is very cramped and getting the original spring clamp back on was very difficult. The hose clamp made it very easy and the seal was just fine. 8.- The new pump functions perfectly- PARTS SELECT delivered a quality OEM product and I am extremely satisfied with their normal delivery which was 2 days because the warehouse was only 150 miles from me.

order part. replace

I watched the video you provided and I could't believe how simple it was. I'm 67 yrs old and I just followed the video instructions.