HDM1853BJ02 General Electric Microwave - Instructions

This is the second time this happened for me. The shaft for the Coupler breaks and will no longer let the plate turn. I looked at the instructions of letting the bottom of the microwave down, etc. and all I could think of is I don't think so. I used the tweezers to try to get the broken piece of the coupler but neither time was it intact. Could not locate the broken part so took the liberty of just putting the new part on the shaft, pushed down and viola I now have a turning table again. I am an 83 age female who likes to try being a do-it-your selfer. Of course there are times I am not successful but. . .By thinking back of why this part keeps breaking I think it may be my fault. I always turn the glass plate around manually when the handle of the cup or mug is out of reach. May be my fault and maybe not. Anyway this time I ordered 2 of the same parts just for future repair hopefully not needed. V.J.

Once we noticed the turntable not working I removed the piece and noticed it was broken at the base of the coupler, took a vacuum and removed the broken piece and installed the new part. Thanks for the help!

Fist I removed the 5 screws under the microwave. Then I dropped the panel and accessed the socket. I removed the socket by removing the one screw and disconnecting the wires. Replaced the wires on the new socket, installed the new bulb and reattached with the screw. replaced the panel with the 5 screws and I was done. Easy

I laid the new tray in the microwave. There was nothing to really install....but, the woman I spoke to in order to order the tray was terrific and I had the part in two days!! I would recommend this company every time!!!!!!

Opened the microwave oven door, unscrewed two screws which held the control panel on, then I removed two of the door switches (each had two screws), and then used the continuity tester to see which one was not operating. It turned out to be the secondary door switch, replaced it and to my amazement, the microwave worked. I have never repaired an appliance before but I didn't want to replace our over-the-stove built in microwave. It was the best day ever when it was working again! The hardest part was getting myself to try the repair.

simply remove broken coupler and install new coupler. no tools required.

damper plate was a snap-in part. rotated fan discharge to top of microwave. installed ducting to discharge food odors outside.

Watched How to repair a Microwave that turns on when the door is opened Video on the web. From this took a shot at the switch was the problem. When I removed the switch it was defective. The small button was in and when you turned the switch upside down the button would drop back into position. Ordered a switch for $25.oo , installed it and the microwave is working fine.

How? I handed it to my husband. Done. Haha. He removed the screws, slid the grill aside, removed the old filter and slipped the new one in place. Replaced the grill and screws, viola'! Quick and easy. No sweat, so swearing. Thank you for a simple solution. It was a pleasure.

At first I thought it was just the bulb, but I wasn't able to find a video of the exact model. The dificult part was figuring out how the vent housing came off (turns out it slid to the left then lifted out) but after I figured that out, replacing the cable assembly and the bulb was really easy.

Unplug appliance, Staring from the rear sides, remove the four side screws. Remove the left and right front screws and finally the front center screw. The bottom panel hinges down toward the rear . Unplug the input wires from the sockets . Unscrew the two retainer screws (one each) and pull the sockets out of the panel. Note that the retainer screws are shouldered. The shoulder fits through the elongated slot in the socket. Screw the bulb into the socket and insert through the mounting hole. Insert and tighten the mounting screws. Note that the sockets may appear to be a bit loose. That's OK because of the shouldered screw. Don't over tighten or you risk stripping the threads of the panel. Plug in the input sockets and install the panel screws in the reverse order of removal. Plug the appliance in and test the bulbs.

Trouble shot first by removing the digital read out face plate panel, lifting it up and out. Found the thermostat housed on the bottom section (found a picture of what I was looking for). It had two connectors. Removed the connectors and noticed that the one looked burnt/melted that was on the thermostat. Took paper clip, connected it with the wires to bypass the thermostat. Plugged in the microwave and power returned. Yes! Ordered thermostat part and changed it out. The new part didn't have a piece that fit exactly into the floor of the microwave so I just made sure it was secure to the bottom. It is only attached by 1 small screw. Fixed!

Removed tiny screw from under the microwave that held the lid shut where the light was located. Took out old bulb and replaced with new one. Very easy!!!!

I did just what videos and instructions on the internet said- Turn off the circuit breaker to microwave and unplug it for safety sake. Unscrew the 6 screws on the underside panel of the microwave.Let it drop down. Remove the old drive motor by unscrewing the 2 side screws and pull out. Pop in the new driver motor; reattach the two screws; put the panel back up and insert the screws. Plug it back in and flip on the circuit breaker and you're done- the turntable is once again turning! So easy even a girl can do it-!

Lifted off the glass turn table and just pushed the new plastic couple onto the drive post. The plastic coupler is splined, so just sit it onto the drive post and lightly turn it until it starts to drop and give a little downward push. That's it - about 30 seconds and the table is turning again.