HDA2000F03BB Hotpoint Dishwasher - Instructions

Repair went very well, parts arrived in perfect condition and quicker than expected. I am very satisfied and will order again in the future.

1. Pulled the upper basket out. 2. Removed the end caps on the tracks supporting the basket. 3. Cussed a little - used a small flat screwdriver to force a flange on the end cap to move far enough to free up the end cap. 4. Removed all 4 wheel assemblies. 5. Snapped 4 new upper wheels and axels into place on the basket. 6. Slid the upper basket into the tracks. 7. Replaced the 2 end caps. 8. Works like a charm.

The 4 rollers and axles needed to be replaced for the upper rack. First, I had to remove the end caps from the upper tracks. This was the most difficult part of the repair. I intially tried to pull the caps towards the front of the dishwasher which did not work. In the end, I twisted them towards the center of the dishwasher. Once this was done, I pulled the upper rack from the tracks, replaced the old rollers and axles with the new ones. Put the rack back on the track. Put the end caps back on. The repair took less than 15 minutes, for something that has be getting worse over the last year.

after removing old door seal, and cporner seals,spent 15 minutes removing many years worth of crud. thensliped in the corner seals, and door gasket, time, about 10 minutes. didn't test, Iknew it would work---- it did.

I popped off the four bottom wheels and snapped these four on. Works great now and doesn't drive us crazy every time we open and shut the door.

popped on new wheels

big project remove old dish rack and replace with mew rack.

The part arrived in three days and matched perfectly. All I had to do was take out the old rack and set the new one on the track and close the door. We recently sold our house and want to leave everything clean and in good shape just as we would expect it to be. I wish replacing all parts was this easy. Bonnie Stanley

My dishwasher used this part # as a substitute for the original part, which i guess is no longer made. After reading the other customers' comments,I thought people were describing two very different experiences with the installation -- some just "popped the cap off the end," or "couldn't be easier." Others had so much difficulty getting the cap off that they broke the cap. I think people must be dealing with totally different kinds of plastic caps. When I started on mine, I couldn't find a way to just "pop" the cap off. It was made so that some small flexible stems or prongs that slid in when installed could not be slid back out. I used a pliers to twist, poke, tilt, bend, whatever I could do to get the plastic cap off the end. That wasn't working, so I tried to bend rims the metal track open, but found the metal was too thick or strong for me to bend it. So I had to twist and force the cap, and the piece that kept the cap on broke off. On one side of the rack it was broken so badly that it couldn't be put back on--kept falling off. Had to try to crimp the rims of the track inward to keep the cap on. It's very loose but it has stayed in for the most part. The cap on the other side cracked enough to get it out without completely breaking off a piece. It went back in better than the first side. Pretty frustrating! I suspect because I don't have the original part with replacement caps to slide in. ?????

Laid on floor remove two small bolts with nutdriver,loose water line with wrench,remove other water line with pliers.Remove water inlet valve and replace with new one

Wow, could not have been easier. The suggested repair stated that the water inlet valve was the problem 93% of the time. And, it was spot on. It was the exact same replacement part. And, once installed, it worked like a charm. I have bookmarked this website, and will use it for all future appliance repair. I simply could not be more pleased. It was a breeze. Thanks,

Removed the existing inner door by removing screws along the edge of the inside door. Had trouble removing the door latch but after lifting it on one side of the plastic door fitting, it eventually lifted out. I also had some trouble getting the spring loaded soap door back into the replacement inner door. After playing with it for awhile I realized that the soap door should be in the open position when putting the spring latch back on. The soap door won't close until you get the entire inner door mounted and back on. I also want to note the the inside vent in the upper part of the inner door needs to be removed from the old inner door and installed in the new one. I missed that at first and it allowed condensation to get inside the door which caused the dishwashers alarm to go off during the dry cycle. One last note that I initially decided not to replace the existing sound proofing material in the new door based on advice from a website that stated that I wouldn't notice the sound difference. That was definitely untrue. I had to disassemble the door, replace the sound proofing and then it sounded fine. Overall it was a little difficult to figure out but considering how inexpensive the replacement door was compared with a having a service repairman come out, it was worth the trouble.

We did not want to spend money for a new dishwasher when the motor is doing just fine. So we went to our local Sears store and were told it would be $200.00 plus tax and it would be 7-10 days for shipping. So we went to partselect.com and ordered an upper and lower dishrack. It was here in 2 days and we paid about $175.00. They were really easy to replace and are working just fine.

Followed the easy to follow instructions. Disconnected water, power, drain hose.. Pulled out unit. Tilted to back, used nut driver to disconnect motor brace, loosened hose clamps. Pulled pump/motor off. Unscrewed off defective part. Cleaned area of debris to reassemble the part ordered. Reconnect everything, reinstalled dishwasher. Turned on unit. No leaks! Dishwasher works great.

I removed the old corner tub baffle's and replaced them with the new one's and that took care of the problem. I used a putty knife to remove the old one's and put some new adhesive on and put the new ones in place and let them set up for two days to let them really set up and they work really good no leaks.