HDA1100N00WH Hotpoint Dishwasher - Instructions

open packages of baffles, installed per video, done, no leak!

The initial problem was that the top rack was difficult to slide out. I purchased a new set of upper rollers. In order to remove the roller you must slide it off the rail. To do this, you must first remove the end cap. I broke the end original end cap trying to do this. The new roller installation was simple. So was the installation of the new end cap. Simply press it on.

After shutting off the water and switching off the electric, I removed the lower panels and disconnected both. I then pulled the unit out and set it on its back. I removed the related hoses and moved the pump to the side. Using a 2" X 6" piece of PVC pipe, I removed the wash arm rubber connector which had a small slit in it and installed the new one with the PVC pipe. After reconnecting the hoses and reversing the process, I powered up the unit resulting in another successful repair with the help of Parts Select.com.

the parts were delivered quickly. i removed the lower rack. the rollers were ready to install. they simply snapped on the post. Done! i placed the rack back in its place and they fixed the problem.

Took lower panel off with screwdriver. Removed old spring. Attached new spring. Very easy, and I'm a woman. LOL

Read Joseph from Livermore, CA for good instructions. I took a camera phone photo for reference before I started. Should have taken another photo half way thru. Probably put the push-on-nut on backwards as it didn't 'lock' in - had too much play in the shaft, would have leaked. Impossible to get nut back off in good shape. I put original mangled push-on-nut on also - it added enough tension to eliminate play in the shaft. No leak..but lucky. Go ahead, you can do this repair for under $20.

Followed the instructions on the website video. Piece of cake! No tools were required. Insert the plastic insert into the wheel ensuring the right side faces the rack. Snap onto the rack once done.

When I received the first order the lower rack didn't fit because it wasn't wide enough. Your people replaced the rack and now all works in good fashion. Thx, phil

Instructions for repairs. Remove old rack from dishwasher. Stop, have a beer. Open packing box. Remove new dishwasher rack from box. Rest. Have another beer. Slidey old thingamajig rack ouy from dithwather. Shove into packing box. Figure out where you put the new rack. Pick up new rack, put new rack on countertop. Hav anoder beer. Put nw wreck in dithwather. Take bx & bee botluls to trash. Take nap. :>) S.

Troubleshot and found that the solenoid had burnt up locking the drain door in closed position. I ordered solenoid, Note: I only received the solenoid. I used the old bracket and springs along with the piston arm for the solenoid. I had to break it free from the old solenoid. Once I got everything cleaned up and put together it took me about 10 minutes to install the solenoid. I manually tested mine prior to wiring back up to ensure proper movement and then tested to ensure that the piston arm did not pop out of the solenoid base.

Installed new ones as per instruction

I ordered the corner baffles and installed them in the corners in just minutes. Repair company quoted me about $100 if they had the parts on the truck. If they had to come back it would be another service call. Did the repairs my self for $24 with shipping charges. Happy Customer

follow your video instruction. very simple.

My machine stopped leaking after I simply massaged the door gasket and cleaned the baffles. I did order the necessary parts, they arrived in a very timely manner and the process was painless. After watching the video for both the door gasket and the tub baffles, when my machine decides to leak again, I will be ready to install new parts. As a snow bird, my machine sits idle for 6 months and I think things tend to dry out. Wonderful experience in ordering and video watching.

When I first noticed my unit leaking I noted that the leak was dripping right in the middle. So, I went straight to this web site with my model number and the 1st part I saw was for a Gasket Insert which is a small piece that completes the sea. I received that part in 2 day and did the repair and I still had leakage. I went back on the web site and looked further and came across info for the Corner Tub Baffles. I did not even know there were there. I removed mine and it was very obvious that the original Baffles were very worn and wrapped. In addition, the unit was quite filthy. I ordered the two replacement baffles. The parts arrived in two days, did the minor repair and now I have no leaks.