Models > HDA1000K01 > Instructions

HDA1000K01 Hotpoint Dishwasher - Instructions

All Instructions for the HDA1000K01
541 - 555 of 608
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water remained in dishwasher after cycle.
Dishwasher is 22 years old and I'm 80 years old so it took longer, about 3 hours. After removing, turned upside down and removed old pump-motor assembly and replaced with new following directions [which took a little while to figure out; my assembly was quite a bit different from the replacement pump-motor]. Pleasantly surprised at how quiet the dishwasher now runs. Normally I would replace this old an appliance, but this unit has provision for inserting a wood panel that blends with the cabinets and a new GE dishwasher with this feature costs $1300 MSRP. I'm trying to save money for when I get old so I decided to do the repair myself. For $150 it was a worthwhile investment.
Parts Used:
Motor and Pump Kit
  • ronald from kirtland, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Two holes not tapped
Instead of purchasing a new dishwasher, I elected to replace the motor/pump assembly which the existing was noisy and leaking water. To start to took pictures of the existing assembly and marked the wiring connections. I read the instructions a few times until I fully understood and had the necessary parts identified. The only problem was the bracket that holds the solenoid has two holes for mounting the drain feedback bracket were not threaded. I was able to tap the holes (metric) and mount the bracket. Caution must taken not damage the solenoid coil.
Parts Used:
Motor and Pump Kit
  • Robert G from Orland Park, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Dishwasher was leaking water on the lower right side.
Merely pushed the baffle into the slots in the lower right corner and the leak stopped.
Parts Used:
Corner Tub Baffle - Lower Right
  • Frances from Garner, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Motor failure because of black power wire separation.
Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.
Parts Used:
Motor and Pump Kit
  • Burl from Spring Valley, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Thank you
By GE dishwasher badly leaked under load. I was about to shop for new dishwasher ($400 ?) when I had found your website. With likely reason identified, inexpensive parts readily available and video instructions being very clear, I had decided to try to fix my dishwasher myself. Parts arrived on schedule and I had replaced my old corner baffles in 1 minute with no tools at all. It fixed the problem with my dishwasher with minimal trouble for me for less than $30. Thank you.
Parts Used:
Corner Tub Baffle - Lower Left Corner Tub Baffle - Lower Right
  • Leonid from Buffalo Grove, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Worn part
Researched the repair solution online, ordered the part from Parts Select that was way less expensive then the manufacture and 2 other parts sites. Very easy to fix. Saved $$$ and time! Love It
Parts Used:
Upper Roller and Axle - Kit of 4
  • Johna from Wilmington, DE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
the tray fall out
Replays the wheel
Parts Used:
Upper Roller and Axle - Kit of 4 Lower Front Dishrack Wheel
  • ARLEY from SUMNER, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Upper Dish Rack kept Falling out of brackets
Watched the how to video, ordered part, part arrived 5 days later. Popped out end caps. Took out rack, replaced wheels and boom less than a minute later it was fixed. Now my kids can do the dishes safely. Momma has a way out of doing dishes now.
Parts Used:
Upper Roller and Axle - Kit of 4
  • Susan from Ashburn, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
wheels won't stay attached to basket when pulled out for load and unload
Original parts broke off at the wheels and wouldn't stay attached to the basket when pulled out for use...replacement was simple strait forward...remove the old, and on with the new.
Parts Used:
Upper Roller and Axle - Kit of 4
  • Larry from Waco, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
front lower wheel broke
Insert the piece into wheel and snap on lower rack of dishwasher. Thank you to parts select for such fabulous service and quick delivery and fair price.
Parts Used:
Lower Front Dishrack Wheel
  • Elizabeth from Deer Park, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
missing top wire basket rollers
Had just a little trouble getting the end caps of the the runner bars after that it was a breeze, I am a 55 year old woman and done the job by myself
Parts Used:
Upper Roller and Axle - Kit of 4
  • Jeanie from Clinton, AR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
upper rack kept falling - upper rollers no longer attached
I watched the video before ordering to ensure I had the right parts. I simply followed the video. So easy! And for less than $20, the dishwasher is repaired. The upper rack was such a hassle, I was considering getting rid of the dishwasher! So glad I found your site.
Parts Used:
Upper Roller and Axle - Kit of 4
  • Julie from Cicero, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
End cap broke
Ordered the part from you and it was easy to replace.
Parts Used:
RACK SLIDE END CAP
  • James from Las Cruces, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
replace pump motor assembly
Too easy- what made it easier was this is a portable roll-around unit I could lay on it's back. Loosen the two clamps around the washer pump, hook up the drain solenoid, washer motor wires, attach the motor hanger, that's basically it. It took longer to make sure I was working from the right set of instructions- this pump covers several models. Once I had that right, it was really a snap. Now the unit is so quiet. It once sounded like a jet engine in the kitchen, now it runs so quiet you can hear the water splashing around inside- a big improvement. We should be able to hang onto this thing for a while longer.
Parts Used:
Motor and Pump Kit
  • Ben from Nashville, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
See below
In replacing the upper rack in our dishwasher, I struggled and broke one of the end caps (see previous tale of woe. With the new end caps, I finished the job in less than two minutes with no tools. BUY END CAPS when you order a rack!
Parts Used:
RACK SLIDE END CAP
  • Leslie from Amarillo, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the HDA1000K01
541 - 555 of 608