Models > GZ2626GEKB13 > Instructions

GZ2626GEKB13 Maytag Refrigerator - Instructions

All Instructions for the GZ2626GEKB13
61 - 75 of 202
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Light switch broke
Popped out the old light switch with a butter knife from the bottom first, disconnected the plug in. Install was just the reverse. Super easy fix
Parts Used:
SWITCH
  • Matthew from Pensacola, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light switch on door broke
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
Parts Used:
Door Switch
  • Donna from Oro Valley, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My Original Armwire Had Fallen Off In The Ice Bin And Got Bent. That Is Why I Ordered The New Armwire Assy.
I removed ice bin and cover that sits ontop of the icemaker. I inserted the longer end of armwire assy first in the front part of the icemaker arm until it clicked in place then inserted the shorter end in the back side of icemaker arm and pressed until it went into the hole all the way through. This was very easy to install.
Parts Used:
Shut Off Arm
  • ROSE MARY from MARYSVILLE, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rear of bucket tilted down holder broken
First I removed the ice bucket from freezer removed 2 screws from the front that hold ice auger in place. Slid ice bucket out replaced new bucket replaced 2 screws returned to freezer.
Parts Used:
Ice Dispenser Bucket
  • Barry from Merrimack, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice would not come through door, troubleshot and determined bale mechanism wasn't turning properly.
Removed old agitator unit - 4 nut-head screws removed, and installed new agitator and screws aligned easily.
Parts Used:
Ice Maker Auger and Crusher Blade Assembly
  • Howard from Montoursville, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice Carrier End Cap
Removed Ice carrier and diassembled the Ice carrier with a socket set. Four screws, cap came right off. Placed the new one on and finished.
Parts Used:
Ice Maker Helix End Cap - white
  • Oswald from Miami, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic wheel in icemaker broke
I removed the ice tray from the freeze. Turn over and remove screws holding the face plate on. Remove the 4 screws holding the crushing mechanism in place. Pull the entire mechanism out and remove the nut holding the blades together. Remember the alignment of the blades. Remove blades and then the pastic crush wheel. Replace in reverse order. Very easy.
Parts Used:
Crushed Ice Wheel
  • Bryan from Lancaster, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker ejector arm broke into.
Removed old ejector arm and installed new part.
Parts Used:
Ejector Arm
  • Mary L. from Millsboro,, DE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
16 of 46 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace ice & water Filter
Open and remove lower cover on filter holder by opening tabs that hold lower cover and remove lower cover.

Firmly hold back of unit and firmly hold and turn filter in counter clockwise to unlock and remove.

Install new filter by holdin back of unit and install new filter by turning in clock wise direction and then replace lower cover.
Parts Used:
Refrigerator Water Filter
  • James from Whittier, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Low Water Pressure
Followed directions on filter unit
Parts Used:
Refrigerator Water Filter
  • John from Ketchikan, AK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing filter
Really easy, simple instructions, and it was on my doorstep 3 days after I ordered. Much simpler than dealing with the appliance store, where I'd have to drive to the store, order the filter, wait 7-10 days, and return to pick it up. Ughh! Internet is the way to go!
Parts Used:
Refrigerator Water Filter
  • Eric from Noank, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
End Cap was broken and ice would not dispense.
Ridiculous how easy it was, REALLY!
Parts Used:
Ice Maker Helix End Cap - white
  • Kerry from DE PERE, WI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water line feeding ice maker was not producing ice
Take out the elbow fill tube and check to see if ice build up inside tube. Clean tube of ice build up. Replace tube back in. In my case that corrected my problem.
Parts Used:
Plastic Tube Insert
  • Daniel from SAINT ALBANS, VT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light out.
Popped out the old switch and replaced it with the one dying
Parts Used:
Door Switch
  • Carlton from CHICAGO, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lip of ice bucket kept breaking off and pieces would jam dispenser.
Took longer to pull fridge out and push back than to replace bucket. Pull bucket and dispenser out . Carefully unsnap plastic front cover and access door from bucket. Loosen two hex screws that attach bucket to dispenser. Auger assembly comes loose. Just reinstall auger and screws then carefully snap front back on. Slide unit back in freezer.Push fridge back in place. Take a beer out of fridge. Drink it and pat yourself on the back!
Parts Used:
Ice Dispenser Bucket
  • Randy from CLARINDA, IA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GZ2626GEKB13
61 - 75 of 202
Back to Top