GW395LEGZ3 Whirlpool Range - Instructions

Replaced the grates. Very pleased. Great service, correct parts, happy customer.

Never repaired an oven before, I just used a screwdriver and went slowly taking this over door apart to replace this glass. I just took piece by piece apart until the glass came out and retraced my steps to install the new glass. Sure glad I did this myself, a new convection oven stove would easily set me back 1,500.00 and......save a bundle on service call fees.

All I had to do was unscrew the pyrex lens over the oven light and then remove the old gasket and replace it with the new one. Worked like a champ!

Purchased 2 piece broiler pan from this site

I researched the problem on the internet, and all of the data led me to believe I had a bad igniter. My husband and I viewed a youtube video about installing a new one, and then I read step by step instructions on another site. We thought we would be able to easily do this ourselves, so we ordered the part from PartSelect, and I received the part within a couple of days. After taking the back off the stove, and the pan off the bottom of the oven, we attached a string and pulled through the old wires, and then attached the new wires on the igniter and pulled them to the back of the stove and connected them. The part was exactly what we needed, and now the stove works like it did when it was brand new! I was very happy with the results! MEF

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Removed the door just like you would do when cleaning the oven; I placed the door on a blanket on the kitchen table and carefully disassembled the door. There were more parts than I expected so keeping track of where everything went was important. I might add that without the use of my cordless variable speed drill motor removal of some of the screws would have been difficult. Adding the weight of the drill motor with sufficient push power I was able to tap the switch which "snapped" the screw loose. Don't think I could have done it with a hand type screw driver without stripping the head. Knowing your tools is very important.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

removed the worn out roller...inserted the new roller....tightened the nut...it was finished...this was without a doubt the most pleasent repair from start to finish..only took 3 days from the time i orderded the part to completing the repair...i would advise anyone to use " partselect.com" without hesitation

Read all others' directions and suggestions. Screw loosening spray was essential to remove the bracket holding the broken piece. Print out the blow-up showing parts from website. Read directions on removing and replacing door in original manual. Lay oven door on counter top front side up with hinges hanging over edge. I prefer a manual screwdriver - less risk of stripping screws. Start by removing screws at bottom edge. Next, side strips and then top piece with handle. Removing layers, being careful to keep them in order and turned the right way. Note the center piece of glass is held in place only by the parts around it so everything has to be tight and aligned. Put back together in reverse order with replacement glass part. My 10+ year old oven is as good as new. BTW I am a 67 year old woman.

Had already removed back covers and disconntedted power. When io received parts I replaced them in reverse oder I had removed them. Took me longer to replace back covers because of my bad diabetic hands. Thanks very much, yopu savbed me a bunch. God bless you and yours, god bless america.

There were two screws holding the igniter in place but one was stripped and had to be cut off with the Dremel tool. Then it was a matter of removing 3 screws from the back of the oven and disconnecting the two wires to the igniter. The description for the igniter implies that there will be screws but I supplied my own to finish the job.

I read all the repair stories here. They gave me the courage to try it. I pulled the oven door out and up. I placed the door HANDLE SIDE UP on a pad on a table. I removed the screws from the bottom and sides and began disassembly. First the bottom, then sides. I came apart easily, I set the insulation aside, then removed the screws and bracket holding the glass. I cleaned all the parts and glass. I replaced the glass and insulation and put it back together in reverse order. I put the drill/driver clutch on low so as not to strip any screws. I checked for tightness with a hand screwdriver. I re-attached the door to the oven by pushing both tabs into oven simultaneously. It took a couple of tries. In all, the fix It wasn't too difficult. I was able to handle it all myself except that my wife helped with cleaning the parts and glass. Now it looks like new again.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.