Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer did not drain completely with water on floor, drain pump frozen.
After unplugging the washer, I drained remaining water from washer tub using my Wet/Dry vac. Ordered new pump Sunday night from PartSelect, 'Standard delivery', part arrived Tuesday morning. Removal & installation took less than 20 minutes.
Use paint scraper to release spring tabs holding front cover on.
Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.
R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).
IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.
Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.
used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.
Removed the bolt holding the agitator coupler on, replaced it and the bolt then slid the agitator on the coupler and the fabric softener dispenser on top of that.... so easy!!
First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help. sincerely, a satisfied customer
Turned off the both the hot and cold water. Removed the hoses from the back of the control panel. Removed 3 panel screws to expose the inside of the component parts. Removed the 2 screws holding the valve. Installed the new valve. Then I pulled off the knob for the temperature control. To remove the switch, you need to press the tab that locks in the switch and turn the switch counter clockwise to remove the switch from the panel. Reverse the operation to reinstall the new switch. Pay close attention to the 4 wires that clip to the switch to get them in proper order. Reinstall the control panel and and reattach the hoses.
Washer sometimes over-fills with water, may even overflow
I followed partselect repair videos to see how to pop off the front panel and also remove the top control panel. Lay the control panel on top of the washer and leave everything connected. With power disconnected I first checked the fill tube and fill sensor by pulling the rubber tube off the bottom of the drum and blowing in the tube - you can hear the sensor click on and off. It requires more pressure if you set the water level switch to a larger load. This behavior told me the tube and sensor were working but this must be an airtight system to be reliable. To test for slow air leaks I blew in the tube to cause the switch to click, then clamped the rubber tube shut with a C-clamp. I left it overnight and no leaks - the switch was still activated in the morning, as I could hear it click when I released the C-clamp. I then suspected the fill valve, so I plugged in the power cord, set the washer for a load and started it. The water started filling and I unplugged the power cord, which should cause the fill valve to shut off immediately. It did not - it kept on filling with water, but in this case eventually shut off after 60-90 seconds. Since it did not shut off immediately when power was removed I knew the fill valve was sticking. I ordered the fill valve from partselect and received it in a couple days. Replacement was easy - shut off water, remove the hoses, and then 3 screws and two electrical connectors to swap out the valve. Then 3 screws to put the control panel back on and snap the front panel back in place. Done. Since replacing the fill valve the washer has been working perfectly.
R&R Leaking/Damaged Hose and replaced it with the new one. One thing to be aware of is that after removing screws from the discharge hose upon removing the damaged one there was some water that did not expel from the unit so there was about a cup of water that came out. After removing the leaking hose you will need to remove the retaining plastic piece so that it can be placed on the replacement hose. Or if you ordered one put it on the hose so that it can retain the end of the hose in the washer. The anti-siphon clip is located about half way up the back of the washer it simply clips in place.
Followed your video instructions and removed agitator.Used 7/16 3/8 in socket wrench to remove bolt in the agitator coupling and replaced coupling. Put new bolt in and tightened. Installed Agitator.Works Great.
I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.
Unplug machine, verified the hot water line to the washer was clear. Used screwdriver to remove top panel from washer. Removed faulty (rusted) temperature switch from seating. Then removed each of the wires from the old switch with needlenose pliers and placed them on the proper area of the new switch. Placed the switch back on the panel and screwed the cover back on. Then plugged the unit back in an tested the hot, cold and warm settings. Easy fix.
We pulled off the bottom cover to access the pump. The washer was on its back and that made it easier to reach. There was two hose clamps to pull off along with the two electrical parts. Very easy to replace.
Full of water and smell like something was burning
This was my daughter's washing machine. I looked at the back of the machine to see if there was an opening to get to the parts. Since the back is all closed up. I knew the front had to come off. I pride up, and I pride out, and finally the front popped off. After taking the front cover off the washer. I could see the belt was all chewed up. We ordered a new belt from partselect and got it a day early. I tried to pry the belt on without loosening up anything. I couldn't get it. So I loosened the four bolts on the motor mount and slid the motor backwards towards the other pulley. I put the belt on both pulleys and pried the motor forward to tightened the belt up. Then tightened all four bolts. Put the front guard back on and tried the washer to see if we had any other problems.