Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Waher would not spin wet clothes.
Tipped washer over on to the front side. Removed back panel. Removed the flex coupling to the water pump. Removed the old belt. Installed the new belt and reversed the process to put components back together.
After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.
Could not turn dryer selection without a pliers. Metal assembly inside knob broke. Easy enough to find knob on website, though the machine was so old the model numbers had changed. Popped off old knob, put new one on; done. Received knob in mail within a couple of days of ordering online. Excellent service. Thank you.
Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there to swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.
The cap just removed by tapping a few times with a screw driver and hammer. then pulling upward it came off and I placed the new dispenser on. a couple minutes saved me from running up and down to add softener and it was very inexpensive.Thanks alot PARTS SELECT.
pulled off cup on top of agataor. scrwed off nut. pulled off agatator. flipted up side down. took off agatator bell wich is on the bottom of the agator. sliped on bell. put agatator back on and scrwed on nut. dont reamber the size of the nut.sorry. put cap on and your done.
Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.
Removed the front panel with a stiff putty knife, removed the worn belt. Placed the new belt on the front pully and than the rear pully, turning clockwise. After checking the spin cycle I put the front panel back on and I was done.
Most washers I looked at do not use a start capacitor but my model did and after testing the capacitor it showed open and was slightly deformed. If you have a this problem the capacitor is located behind the front panel about half way up on the right side zip tied to the side of the washer. It is always good to check the capacitor before spending big bucks for a motor you may not need.
Remove four screws which held the front cover of the washer. Dropped the cover down to expose the temp. switch. Turned the switch 1/8 turn counterclockwise which removed the switch from the cover. Pulled of the four pigtail wire leads and then installed the new switch in reverse order. Very easy!!
Open back cover and found that drain pump had a bad seal. Took it apart and bought new seal some what same size. Put everything togather and start washing clothers and wife complained that it became wost the before. When on line and found pump and price was just right to take a risk. Ordered on sunday and got ups tuesday. Replaced pump on Sunday and leak was gone and wife was happy.
------Got chicken and beer that Sunday--------------
The hose has a tapered end that fits in a tapered hole in the back of the washing machine.When insalled the first time,the joint leaked badly.My solution was to coat the hose end and the interior of the hole in the back of the washing machine with silicon sealant;let it set up for a few minutes and install the new hose.This solved the leak and the hose seems to be working fine now.