Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Fridge getting warer and warmer
remove back panel inside fridge freezer side, everything frosted, unplug and used a hair dryer
1. Took out defrost heater and the bottom and tested (per this site) tested OK.
2. Then looked at the defrost thermostat, it was swollen with the top coming off. so i new it was bad 3.clipped and stripped the 2 wires, spliced in the new one with wire nuts and sealed them with silicone. All better
took the back off and defrosted with a hairdryer. disconected the part pulled the part out cut the wires. put the other part on and instaled it. put it back together and it seems to be working just fine. thank you
The original fan had its blades sheared by ice build-up
The original design is poor. The evaporator fan is mounted in an upright position just below the ice-maker. A plastic grate mounts over the fan assembly to allow for air circulation. Unfortunately, random chips of ice from the ice maker can fall into the fan, causing the fan to shear its blades. Replacement of the fan blade is relatively simple (accept for having to completely unload the freezer and remove all back covers, the ice-maker auger motor assembly, and the metal evaporator cover). In order to mimimze this from reoccuring, I installed a 1/4'' mesh metal screen over the exhaust ports on the cover. Thus far, this has worked well to keep ice chips out of the evaporator fan.
Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.
I replaced the three sensors, 2 in the freezer 1 in the refrigerator. This was rated as the most common problem. Did not fix the problem. I then checked the ohms on the new sensors then the old sensors they were all within .5 of each other. So I got smart and went down the list of causes on their list. I emailed partselect and asked what the parts should read. They replied with that information and it turned out to be the voltage converter on the compressor. I ordered the part on friday payed for overnight delivery and it arrived tuesday. This as you can imagine makes me angry. But the part was easy to install and my refrigerator started working right away. I would advise anyone with this problem to start at the top of the problem list use a multi meter check everything on the list and only replace part or parts that don't come up to standards. This will save time and money and hopefully fix the problem the first time as you are not switching out parts and hoping that it solves the problem.
Removed the divided glass shelf, to which the slide rail is attached. Removed the broken rail, saved the two screws. Now comes the clincher: It would help if the replacement part website would tell you what size and what kind screwdriver you will need, so you could start chasing it while you wait for the part. Even better if they could include it, since the plastic part and it‘s shipment is not exactly cheap. So to screw in two screws you need a #15 Star screwdriver! How many housewife’s have this one in the tool drawer?
I simply removed the old seal on the refrigerator door and replaced it by just pushing the new gasket seal back into place. It was a very easy repair to do.
Replaced Defrost Thermostat. Tricky removal of light fixture cover and evaporator cover. Light cover screw removal is not intuiitive and the eveaporator cover tabs are not easy AT ALL to remove.Once they are removed, simply 2 screw removal of rear panel.
Had to unscrew screws holding cooling coils to gain access to thermostat mounted on a coil in rear.
Simkple matter to cut wires, remove old thermostat and splice replacement back on. Found it simpler to re-mount thermostat on top coil greatly simplifying process.(Why didn't they place the original unit in this much more accesible place?) Re-attach coils to rear wall replace rear panel, light fixture cover and evaporator cover.
Refrigerator has been running fine this past week.
1 opened door 2. pryed cover off from cieling 3.cut and stripped wires on 4. sodered wires from old wires to new sensor. 5 insulated conection.6 put cover back on. This did not fix the problem it was the control moduel.
Open the freezer panel which attached with screwws and locate the defrost thermmostate behind the back pannel. Cut off the old thermostat wires and connect the new wires.
diagram from part select matched my fridge perfect. i ordered all parts that involve defrosting coils. ( defrost heater 618, defrost thermostat 620, defrost thermostat 627 ). two wires involved with thermostat, just removed all old parts and replaced with new. Part Select videos helped demonstrate the projects well.
