Models > GSL25IFRFBS > Instructions

GSL25IFRFBS General Electric Refrigerator - Instructions

All Instructions for the GSL25IFRFBS
1636 - 1650 of 1857
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken auger
After watching the video twice and having my iPad handy I was able to effect the repair with a minimum of problems in about 40 minutes. The video was a tremendous help.Thank you very much.
Parts Used:
BUCKET AUGER
  • Norris from Surprise, AZ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
cracked trim
push in
Parts Used:
Recess Trim - Black
  • tom from santa monica, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Ice Bucket Auger broken
Removed all parts to get to the LEFT Hand Thread nylon nut that holds the auger in place. I used a stiff putty knife inserted in the slot of the LEFT Hand Threaded nut to unscrew the nut and then when finished to tighten the nut. Also be careful when removing the plastic covers as they are held in place with plastic catches that can break. I used a thin flat blade screw driver on each side of the covers to gently pry the covers apart. Also note the position and number of the metal fingers and nylon spacers on the auger, a photo of the assembly is helpful.
Parts Used:
BUCKET AUGER
  • T. from Argyle, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Slide r ails were broken
Piece of cake...did it myself, didn't even need to ask my husband
Parts Used:
Drawer Slide Rail - Left Side Drawer Slide Rail - Left Side
  • Kathy from Kiawah island, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Frost in ice dispensor
Had to take front panel off dispenser area. Then remove components and install new part. That was easy part. Problem was getting components back into front of freezer. Seemed like something was blocking it from going all the way in. Had to remove small amount of insulation and "jiggle" components and eventually fell into place.
Parts Used:
Dispenser Door Assembly or Flapper
  • David from Saint Johns, FL
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
ice flapper would not close
The first thing I did before starting the repair was watch the 2 videos. I followed the directions step by step and within an hour I had a functioning ice maker again. I had searched all over the web and the other sites were of no help. Your site really made it easy to figure out the problem and order the right parts. I now have a problem with my dishwasher so I will be back on your site soon. Thanks!
Parts Used:
Dispenser Door Solenoid Assembly Dispenser Door Assembly or Flapper
  • Louis from sloansville, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Fridge Side Freezing/Too Cold
Followed the repair video, was spot on!!
Parts Used:
Temperature Sensor
  • michael from silver bay, MN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Broken plastic on Auger and Chilling Shelf
The two parts came faster than expected, which was a pleasant surprise. All I had to do was open the box, wash the new parts and place them into the freezer. So easy!
Parts Used:
Chiller Shelf - White Refrigerator Ice Bucket and Auger Assembly
  • Karen from Rio Vista, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Ice dispenser not putting out ice
Followed instructions from Visio, made repair easy. Thanks for the instruction Visio.
Parts Used:
BUCKET AUGER
  • A Jack from Fort Worth, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Leaking water from outside top right rear of ice maker tube
Turned off water supply, removed bottom rear metal panel,with a towel to catch water pushed in and removed water line from double water outlet, removed metal clamp and then grommet tube assembly from top right rear of refrigerator. Then I put in new grommet tube assembly, turned on my water and checked for leaks.
Parts Used:
Grommet / Tube Assembly
  • David from San Antonio, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Frig was not making ice.
Removed the faulty ice maker in about two min.. New unit was installed in approx. five min. Watched your video prior to installation and it helped greatly.
Parts Used:
Ice Maker
  • robert jr from east rutherford, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Refridgerator and freezer getting warm.
First replaced the temp sensor and thermostat, no results. Replaced heating element (looked chared inside the clear tube) and it worked. Heating element is just a plug in connection as comparewd to sensor and thermostat which is splicing in wire connections. Defrosting takes the longest time.
Parts Used:
Defrost Heater and Bracket Assembly
  • Paul from strongsville, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
the plastic is broken
unmount the original and mount the new
Parts Used:
BUCKET AUGER
  • Dalilah from Coral Springs, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Fan wasn't running and walls of freezer and ref. were hot
took screw that holds motor frame in place out with nutdriver, rolled motor frame out after unplugging motor,took screw out of strap that held motor in frame, removed bushings from old motor and put them on the new one and re3versed the proceedure.
Parts Used:
Condenser Fan Motor
  • MICHAEL from Lubbock, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
not defrosting
removed shelves and rear panel. cut wires, spliced in new part used wire nuts and filled wire nuts with silicone, replaced back panel and shelving
Parts Used:
Defrost Thermostat
  • Claude B from Spring Grove, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GSL25IFRFBS
1636 - 1650 of 1857
Back to Top