Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Loud knocking noise with the evaporator fan
I had taken the noise long enough and wanted to get this repaired. I didn't want to pay a repair man hundreds of dollars to do it so i decided to do it myself. I went on to YouTube and found a few videos that showed me how easy it was to do (very helpful).
I wasn't so sure all that noise would come from the Evaporator Fan motor so i ordered it and took the chance. For the small cost, it was worth the try.
All went well accessing the unit and removing the old part. Very fast indeed. However, the snag came when i went to plug in the new part electrical to the existing electrical adapters. The old part had 4 lead connections. The new part had 6. and the wires on the new part were different colors than the existing. I had to use some logic and courage to cut the wires on the new part and rewire the old adapter to this piece. Luckily, i wired everything correctly.
Calling Part Select got me a phone number for the parts manufacturer to help with the splicing but i opted to do it on my own.
The result is i have a noiseless refrigerator again. What should have taken 10 to 15 minutes took half an hour because of the wiring but overall, very easy.
I watched the "how-to" video on the website and decided that I needed to disassemble the icemaker first (before ordering parts) so that I could make sure I was ordering all the parts necessary for a complete repair. Good thing I did. I didn't notice the cracked cover and chipped nut until I had the icemaker all apart. I then ordered the necessary parts. When they arrived 2 days later, I set up a table near my computer so I could re-assemble the unit as I watched the repair video...pausing the video as necessary. It all went without a hitch and worked perfectly when re-installed in the freezer. **Note: I left the old parts out of the ice bucket while I was waiting for the new ones to arrive...taped up the gaping holes in the ice bucket with blue painter's masking tape and re-installed the bucket in the freezer with the icemaker on...so I could still manually retrieve ice out of the bucket. I left the switch on the front of the freezer door in the "water" position to remind me that I couldn't dispense ice. Water dispensing worked fine. The video is the key. Impossible to make a mistake if you pay attention.
Read your instructions, which were very helpful, and followed them to install. It took a while for me to realize that the threaded cap at the end of the auger was a left-hand thread. Other than that, I had no problems.
After figuring out how to remove the old broken clip, replacement was easy. Had to use a small putty knife to open the release on the bottom underside of the clip(between the clip & the refrig) . By looking at the replacement piece it was easy to figure out.
Auger asm had broken off part of blade at end of auger and would not rotate ice out of dispencer.
Removed 3 screws from end of ice storage box,then removed auger asm.Removed c clip on end with flat screwdriver, then disasembled ice crusher blades and nylon/plastic washers.Carefully staging them for reassembly in the correct way.Use pliers to reinstall c clip after new auger is installed
Auger broken, and clear plastic piece at exit of bucket broken.
Pulled old assembly out, emptied ice, installed new assembly, filled with the ice already made. Less than 1 minute. Worked like new for a week. Now, auger won't turn. Have no idea what the problem is, but I'm assuming it's the motor that turns the ice bucket auger, because the auger turns by hand. The bucket ass'y. was in need of replacement, but now I'm wondering if it was worth the money because of this new problem.
removed the depenser or ice collecter disassyble,replace the new auger and install the collecter tray in freezer.the bulbs i got was for use as i needed,at a later date i have not been able to fine the ice and water depenser bulbs on the open market.
Part arrived very fast as ordered..need to pry old switch out from top..use care to push the retainer down..after old switch was 1/2 out, I used a putty knife for better leveridge.Remove wire connector...after plugging in the wire connector to the replacement switch, make sure the switch is properly positioned so the switch will depress when door shuts.
This repair was very simple to do. I cannot say enough about part select dot com. I feel that I am a definite handy man yet the videos on the part select dot com site proved to be valuable. This video showed and reminded me that the plastic bushing holding the auger on was reverse threaded. Being a rightee tightee leftee loossee person embedded in my head I would have worn out that bushing holding the auger in place. I recommend not only purchasing from partselect.com YET please watch the video on this site prior to this installation. This made the installation not only simple yet informative. Thanks!
look very carefully at the picture you provided in the parts fish, removed the ice maker tray and the rest was very easy ,i saved alot of money and time doing it myself.
My GE refrigerator emitted high pitch noise a short while ago. I tried different dampening methods that helped but not eliminating the problem. I finally replaced the fan, motor, and associated parts and solved the problem. The total cost was about $50.
Moving the refrigerator into my new (very old) house we had to remove the doors which resulted in a crimped hose and union
Remove lower front panel, disconnect damaged union from water hose under freezer door, replace with new union, tighten and reattach front panel. No more water coming from under the unit. Ice maker and dispenser features returned to working order!