Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The rollers on the upper rack broke
There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece then slide the rollers out. Place two new rollers in the rail and put the plastic end piece on. Use the hammer and punch to bend the metal clip back into place. Snap the rails on the rack and set the rack on the guides in the dishwasher. Replace the top guide using the screwdriver, you will have to twist the rails in order get them in between the guides.
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.
Open the tiny plastic package in inserted the wheel onto the "axle". Opened the dishwasher, pulled out the bottom rack and snapped the wheel onto the rack. Done!
The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.
The stud assembly in the middle of each wheel no longer stayed inside the wheel.
Just pulled off the old wheel. I just had to push in the stud to the wheel and pushed it on to the rack of the dishwasher. Very easy repair! Only disappointing part was that it bothered me to have to purchase the stud with the wheel. I was told they only came as the set. I only needed to purchase that inside stud. My wheels were fine.
1. I removed the plastic stops from the ends of the upper rack slides. 2. Removed the upper rack. 3. Unclipped the old rollers from the rack. 4. Clipped the new rollers onto the rack. 5. Made a grunting noise so the wife could hear. 6. Walked away
I removed the four screws holding the screen and molded plastic cage inside the rear of the dishwasher to expose the check valve assembly. I then unscrewed the piston and nut assembly with my hand and replaced it with the new one. I found that the rubber cone shaped valve on the old piston and nut assembly was entirely disintegrated. This easy repair solved the problem.
lower rack took one min. take out old slide in new
upper rack a little tricky had to remove end caps on rack arms to slide rack out to replace rollers. end caps are not snapped in they have a lever in the track that is part of the cap if you twist it a little cap will slide off. total time for this part 15 min.
The bottom rack was a breeze since it wasn't attached to anything. The more difficult task was removing the plastic rail guard for the top rack. With some elbow grease and ingenuity, I finally figured out that it must be tilted prior to being popped out of its socket. Follow the same procedure after replacing the rack.
Dishwasher leaking at rubber connector - pump wash arm
First removed dishwaser from under counter so I could get to rubber connecter. It is located in center under dishwasher. I first needed to unscrew with wrench rubber connection at pump and and then the complete piece unscewed by hand from pump wash arm. I then just had to screw new rubber connector back on to bottom of dishwasher and re-attached at the pump. It was very easy to replace the rubber connector. I also replaced the dishwasher sump housing because it was made of same rubbber material and feared it was deteriorating also. I had to unscrew with wrench at pump as well and it just popped out from inside dishwasher after unscrewing screen inside dishwaser. Popped new piece in and screwed screen back on and reconnected underneath dishwasher back to pump. The rack roller wheel just popped right on. FYI: The wheel is actually 1.75 inches in diameter not 2 inches. I was worried it might be too big if it where 2 inches but it was the same size as the other wheels which was 1.75 inches. The hardest part of this job was getting the dishwasher in and out from under the counter. The good news is that most of these parts are standard and the replacement parts fit perfect.