Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
water into bin (big frozen chunks)
, to remove the inlet tube holder/guide gadget thingee: (1) remove the three Phlipscrews from the motor end of the housing. (2) pull the housing straight off the end. (3) remove two Philips screws in deep holes that hold the ice tray onto the motor housing. (4) this frees the ice tray assembly, which you have to pull out, freeing the rotating blades, from which (5) you slide the sxle out of the middle of the inlet-tube thingee, so (6) you can then remove the inlet gadget from the ice tray.
You then reverse these instructions to reassemble with the correct inlet gadget. The tricky part is the front cover that hides the ice-tray from view. That cover has a couple of ears that have to fit into mating holes in the motor housing before you replace the two deep-hole Philips screws that hold the tighten the ice-tray assembly back onto the motor housing.
So it's too bad they don't see the ice-maker assembly with all the knock-outs inplace, so you can knock out the one you want. Other than that, it would have been no more trouble than other people have reported in working in the tight space inside the freezer compartment.
Refrigerator and freezer compartment gradually get warmer, frost buildup on back of freezer compartment.
Remove freezer contents, shelving, baskets, shelf brackets, basket rails. Then, remove the icemaker including the ice basket, the cube freezer and the motor assembly. Remove the back liner of the freezer compartment. Remove and replace the defrost heater assembly, using the old mounting brackets and connecting the wires to the same terminals. Reassemble. Discard excess screws :).
Removed the old icemaker and installed the new one. The first one we ordered lasted about 4 weeks and pooped out. Parts Select was very nice and gracefully sent another in two days time. This one has been installed and is working fine...Hope it stays that way.
Took under 5 minutes. Removed two screws and unplugged the wire bundle from refrigerator. Removed old unit. Put old wire bundle on new unit. Plugged wire bundle back into refrigerator and remounted the new ice maker. Could not have been easier. Watched the video first, it was very helpful.
This was a very easy repair. Of course start by unplugging the power cord. Take out the lower freezer drawer. Unplug the wiring harness from the ice maker at the rear of the freezer. Undo 3 screws with a 1/4" nut driver. The ice maker will come right out. You don't have to undo any water connections, the feed tube just slides into a guide in the ice maker. Once the ice maker is out, unplug the harness from the old one and snap it into the new one. Same with the cover. Reassemble in reserse order. Plug the power cord back in and wait a couple of hours for the familiar sounds of ice cubes falling into the tray.
After going to manufacturer's web site and customer service phone, was unable to locate the correct switch in the dispenser area on the door. Your web site had the picture of the switch and it was right on and in stock. Shipping was quick and inexpensive. Repair went quick and all is well.
Ice maker putting black pieces of plastic in the ice
Replaced ice ice maker using All of the instructions on the website. Very easy. A couple of the screws I had To feel for because I couldn't gety big head In the freezer far enough to see them. Very simple and only took about 15 minutes.
Frist pulled everything out of freezer put in refridge then took out ice maker box then removed ice maker motor removed back panel took hair drier defrosted the coil then removed bracket screws that hold heaters in place removed bad heater, the hardest part of the job was getting the wirers back around the coils when done just reversed the process.I have a side by side so there was not a whole lot of room to work with. I only weigh 160 lbs it was a tight fit for me. But all in all it went well. Thanks
Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.
Turned out the defrost heater has burnt out in the freezer compartment on both heater tubes. To get to it. 1) take out all the shelves 2)remove the light bulb 3)unscrew 6 screws for back panel 4)Mine had a lot frost build up on the evaporator coils which I used a portable heater to defrost. which it took about 2 hrs to get all the frost thawed out. 5) Defrost heaters are located below each of the coils remove 2 screws on each plate there are 2 plates holding the heaters in place. 5) You may have to bend the sheet metal in order to get the heaters out and trace the wires to where it connects to towards the top or the freezer. 6) Put in the new heaters and plug in then put back together. 7) I also replaced the Defrost thermometer which it is easy to replaced while I had it apart. Now the fridge works perfect just like new.
It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.
Old ice maker leaking water and produced ice cubes with black inclusions. First, I removed old ice maker per video instructions. Transferred electrical cable, cover, and bail to new ice maker. First installation failed because I failed to make sure water tube correctly enter back of ice maker. No ice. Initially thought electrical cable wasn't firmly in place. Then I noticed frozen water dripping down back of freezer. A clue! Removed ice maker and reinstalled making sure water tube went through the hole in back of ice maker. Now the new ice maker works beautifully!
I went by the video but my removal and installation were different than shown.
Instead of the ice maker unclipping from the wall after one 1/4" screw being removed from the bracket, I had to remove three of the 4 Phillips head screws from the ice bucket slider below the ice maker and swivel it down to allow the ice maker bracket to clear. The two 1/4" screws holding the ice maker to the wall at the top had to be removed and then the ice maker could be pulled away from the freezer wall. The rest of the instructions went according to the video and went well.
