Models > GLEQ2152ES0 > Instructions

GLEQ2152ES0 Frigidaire Dryer - Instructions

All installation instructions for GLEQ2152ES0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GLEQ2152ES0
241-255 of 298
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loud squeeking and vibration of the dryer drum.

  • Customer: James from Centennial CO
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the directions sent by you step for step and the rpair was done in no time at all. Had a little trouble with the roller ball installation but figured out how to install it after a couple of tries. Repair was done with minimal use of standard houshold tools.

dryer squeaked

  • Customer: Cathleen from Port Orchard WA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
It was easy, I handed the part to my husband and he did it!!!!!!!!!!!!!!!

High pitch squeaky dryer sound

  • Customer: Mohamad from Chicago IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I have a washer-dryer combo unit, so the repair steps were slightly different than the repair videos I watched. (1) removed the screws at the top of the dryer and remove the top. (2) removed the front control panels and unscrewed the front of the dryer (where the door is mounted to). (3) from the back of the dryer, removed a small metal sheet to access the dryer's belt and dismounted the belt from the motor. Finally, lifted up the dryer drum and take it off the dryer. Once this done, I used the rear drum bearing kit and replaced the assembly that hold drum from the dryer back. This was a straight-forward and did not take much time. Unfortunately, the belt I purchased was a bit short, so I kept the old belt during the assembly.

Rear drum bearing squealing

  • Customer: Debra from Deming NM
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I went online and viewed a you tube video on replacing the rear drum bearing on the brand of my dryer. After reviewing this, it was pretty easy since I new what I was getting into. It really helped! Most of the time was spent cleaning up the inside and outside of dryer first before the parts replacement. Other time was spent in putting back the dryer where it came out of. New dryer replacement would have been $750.00 plus labor costs modifying the area where it had to be placed which may have included relocating a shelf and re-routing the dryer ducts. Total cost was around $50.00 plus my time.

Door handle broken on front load dryer

  • Customer: Mollie from Williamsburg VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Simply removed the old broken handle screws and replaced it with the new one.

Dryer was making a noise like scraching a black board.

  • Customer: Randy from New London NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair went very well.The biggest problem was the spring on the tension roller when putting back together.But it just takes a little bit of patients and it was fine.Works great now.

Broken Belt

  • Customer: Peter from Cocoa FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Brought up repair video on my smart phone and followed instructions while doing the repair (pausing when needed) and completed the job in under an hour including vacuuming the lint from inside the dryer before re-assembly.

CHANDE MOTOR AND BELT

  • Customer: James from Tidioute PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug the dryer from out let, Lift the lid (top of dryer), cut the zip tie. Pull the two wires and the plastec wireing harness apart. Remove the screws that holds the front panel on, and the screw and molded pice that holds the drum in place, remove the belt from around the drum. Now remove the drum, have to lift up and out on the drum. Remove motor, and pulley from old motor for use on new one. Put everything back together. Took me 15 to 30min to do this ( I recamend a new belt as long as you are this far and the price is a small amount for it.)

Dryer over heated tripped thermal limiter

  • Customer: Kenneth from Carmel IN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took apart dryer and replaced limiter located on back, reassembled dryer and tested wiithout connecting to vent. Dryer working fine without vent connection. However as always something simple turns to disaster when children help. While cleaning out lint from dryer vent which I will say was the original problem causing the limiter to trip, youngest son wanted to help. Son did not know that to walk in an attic you must step on joists not drywall. No one was hurt just banged up falling into the garage. Extended repair to ceiling added dificulty factor of 2 days and a bit of insulation clean up. Good news is the dryer works fine and the vent is no longer clogged up with lint. Watch your help it always adds to the repair.

noise

  • Customer: Daniel from San Marcos CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
i folow the instructions from web page

motor did not start

  • Customer: Luke from Williston ND
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed back panel, unplugged motor and released the belt. Remove top panel then front panel. Remove drum for better access. Vacuum the lint while everything is open. Remove old motor and replace with new motor. Reassemble. Suggest replacing the belt too.

Symptoms suggested drum support bearing was problem.

  • Customer: Calvin from Las Vegas NV
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 0 of 0 people found this instruction helpful
Referred to Video and replaced drum support bearing as shown. Did not solve the problem as noise was still present. Called professional repairman, who replaced the belt pulley, along with all the parts I had just installed (came as part of a total kit). I was on the correct path, but just didn't go far enough to check out the belt pulley. If it should happen again, I could complete the whole repair process. Great learning process!!

DRYER HEATER ELEMENT

  • Customer: William from Temple GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
THE PART FIT PERFECT REPAIR WAS SIMPLE THANK GUYS FOR YOUR HELP U ARE THE BEST/REMOVED THE TOP/ FRONT FACE /BELT & DRUM REMOVED OLD ELEMENT INSTALLED NEW ONE DRYER WORKS PERFECT THANKS AGAIN

Shreking noise when turning on, then loud noise from dryer, after a few minutes it would not be so loud but louder than normal.

  • Customer: joan from Roanoke AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced everything on the dryer till I got the right problem, seriously, I now have a new dryer in an old body, still came out alot cheaper than buying a new one. I listened to every sound on youtube but none sounded like my dryer.

dryer stoped working

  • Customer: Larry from Jewett city CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
opened top of dryer, remove blown part and installed new part very easy.
All Instructions for the GLEQ2152ES0
241-255 of 298