Models > GLEQ2152ES0 > Instructions

GLEQ2152ES0 Frigidaire Dryer - Instructions

All installation instructions for GLEQ2152ES0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GLEQ2152ES0
256-270 of 317
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Belt & drum bearing

  • Customer: Brian from LOXAHATCHEE, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Had the drum bearing but had never got a round to putting it in we just let it squeek. Then the belt went. Easy enough, whatched the tutorial once and just did it. 35 minutes and back drying.

Dryer was not heating

  • Customer: Jessica from Iowa City, IA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
We followed the how-to video. It was actually easier than the video made it look. Our dryer had a removable panel behind the pulley to put the belt back on easier. We had to take the whole dryer apart, but it was not difficult at all. We replaced the heating element and put it back together. If you can screw a screw, you can do this repair. Our dryer is working good as new. I love this site!

Early in the cycle, dryer was making a loud noise

  • Customer: Charles from Kinston, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
As the clothes began to dry and got lighter the noise stopped. Apparently the noise was the result of the rear lower portion of the drum scraping the heater coil due to a well worn upper front felt seal. To repair; I watched a how-to-repair video that was posted on the internet and after watching it, everything was easy.

Dryer Heater Not Working

  • Customer: Daniel from North Port, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I never respond to any of these surveys, but in this case ill make an exception because they made it so easy and parts were received correctly a quickly. Thanks, dan

Loud Squeaking

  • Customer: Rene from Bell Gardens, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Very simple. Pop the top open released the beld from the back it's easier that way the video was very helpful the sound was so bad you can hear it from a few houses down after year of just using it like that I figured I ha d nothing to loose great price great instructions now it sounds just as new.

Broken Drum Glide

  • Customer: Stefanie from Columbus, MT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I viewed a video online and my repair was as simple as the video showed. Love that I am able to do quick fixes like this! Thanks Partselect.com!

Lint filter was broken

  • Customer: BeLinda from Indianapolis, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
All I did was insert the new one! Service was excellent. I received it in one day!!!

Door handle broke on one end

  • Customer: June from Wilmington, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I had to grip the broken piece that was still attached to the screw with a pair of needle nose pliers and then unscrew it from the back side. After taking the screw out of the other end,I just put the new handle on and screwed it in. Very easy!

Dryer was make a really bad squealing noise

  • Customer: Ken from Pinole, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Saw video on YouTube on how to change rear bearing. Followed what I saw and repairs were made with ease. our repair kit included all the parts (new bearing) and everything fit perfect.

The belt broke on a squeaky dryer

  • Customer: christopher van from Milford, NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I raised the top up by releasing the two clips in the front edge with a small flat head screwdriver. I used a bungie cord to keep the lid from bending to far back. I removed the front of the dryer softly letting the drum rest on the insides. I carefully removed the drum by pulling upward to disengage the rear bearing and not damage the heating element. I then cleaned the entire inside of the dryer with a vacuum, brush, and some compressed air. I then replaced and greased the new plastic bearing cup, installed the drum, slipped the belt on, installed the front cover, and hooked up the belt through the access door on the rear of the dryer. Checked to see if the system looked ok and closed the lid. Worked great. I would order a front seal felt kit also if I was to do it again.

Cracked

  • Customer: Gary from Girard, KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Took cover off and removed damaged part. Removed wiring and reattached to new part

Bearing And New Belt

  • Customer: steve from mountain home, AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First I watched the video on how to do the repair. Very good instuctions made the repair go smoothly.

Door would not close because of broken female latch.

  • Customer: Raymond Frattone from Richboro, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Very simple. I removed the broken latch with pliers and snapped in the new one in less than 5 minutes.

Loud squeaking noise

  • Customer: David from WASHINGTON, DC
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the video. Very helpful. There is no way I could have done this on my own without that guidance. Parts in Rear Drum Bearing Kit included new screws and metal support parts that are shown as reused in the video. To install these parts, I had to hold the back plate in place. A big piece of masking tape did the job nicely. The only major problem was tapping the holes in part that attaches to the drum -- very difficult. Needed my best Phillips screwdriver, leather gloves, and a lot of hand strength to get it done. I had to slightly ream out one of the holes to make the last screw fit. Minor problem - the idler arm is not retained by anything. The idler pulley and arm both fell off when I reinstalled the belt. I guessed right on how to get them back on the machine.

loud squeek

  • Customer: Cheryl from Weirton, WV
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
followed the Video instruction which were provided. Dryer works like brand new.
All Instructions for the GLEQ2152ES0
256-270 of 317