Models > GLEQ2152ES0 > Instructions

GLEQ2152ES0 Frigidaire Dryer - Instructions

All installation instructions for GLEQ2152ES0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GLEQ2152ES0
151-165 of 298
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

loud scratchy noise

  • Customer: david from edinboro PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
first and foremost, watching video on replacement/repair was key to success.furthermore, i ordered part one day and was at my doorstep the following day. the installation process took approximately half of an hour which included vaccuuming cabinet of lint.

Dryer was making loud squeak

  • Customer: William from Flowery Branch GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 1 people found this instruction helpful
This was for my Daughter's dryer. A helper really makes this quick and easy. First of all-UNPLUG the unit from the wall. I pried the top up with flat screwdriver. Laid the top back against wall. Removed the two wires from the door cut-off switch. Then removed the two screw attaching the front to the cabinet. Removed the small access panel on back of cabinet. Depressed the belt tensioner to release pressure on the leather drive belt. Went back to front, pushed the belt to the rear of cabinet, then lifted the back of drum to pop the bearing up and out of the plastic cup. I then tilted the drum forward and down and removed through front of cabinet. Reached inside the drum with Phillips screwdriver, removing the two screws to realease the bearing and BB bracket from back of drum. I attached the new bearing cup with BB to the back of cabinet, filling the cup with the high temp grease provided in the cup. Before installing the new bearing on the drum, I ran the new screws into and back out of the new bearing to cut the threads, making it easier to attach on the drum. I then put the drum back into the cabinet popping the bearing into the top of the plastic cup. Next I went to the back, put a bit of grease on the shaft that the tensioner bearing rides on. I re-set the belt on the tensioner, making sure the belt was back in the original position around the drum. I then re-attached the front cabinet centering the front of the drum on the felt. This felt supports the front of the drum. I manually gave the drum a few turns to make sure the drum was centered properly, and belt was mounted correctly. I then re-attached the two wires to the door switch. Slid the dryer into position, inserted the plug back into the outlet. Turmed it on, and now the dryer runs like new again. My Daughter is happy again. You will want to have a vac handy because it is unbelievable how much lint and dust are in the cabinet. I also took the filter bracket apart and cleaned it too.

The dryer was squeaking.

  • Customer: Kara from Doylestown PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
We followed the video exactly. The video itself was simple and straight forward. Our model was a bit different than the video's example. The video's example had their spring action for the belt configured differently. When we finally figured out the difference, we were able to finish the job within minutes. The dryer now runs like new. We aren't mechanically inclined. That's why it took us so long. I still would recommend this company to anyone because it saved us time and money. The video really helps!

Squealing (loudly!) Rear Drum Bearing

  • Customer: BRUCE from STANDISH ME
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
Parts Select has my high praise! Everything from the ease of the on-line ordering system to the video on how to install the parts (very well done!!) to the quick deliver...all was very impressive. My wife thinks I'm pretty cool that I was able to pull this repair job off and I definitely will come back if I need another part! Thanks for helping this "weekend warrior" shine! Bruce.

Broken belt or wore out !

  • Customer: Mary from Devine TX
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 1 people found this instruction helpful
Got the belt for my little bro's dryer . . . he and a friend tore into it without looking on how to do the job . 2 hours later dryer apart not fixed . . . LoL . . . Next day I get a Call asking me to find a repair manuel . . . I laught and told him to go to Youtube on his phone and the video would tell him how to do it ! He is back up and drying . . . Moral to this story . . . look before you leep !

Squeaking noise as the drum turned

  • Customer: Doug from Silver City NM
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead and get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.

Heating element went out

  • Customer: Susan from Brandon MS
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Our heating element went out on our Frigidaire Affinity dryer. My husband is good at repairing things so we decided to order the part and do the repairs rather than hire a service technician. Before looking at the dryer we thought the back could be unscrewed and taken off to give access to the element but it did not. He had to take the dryer drum out to access the element. It was easy enough for him to do though and since we had everything opened up I was able to use the shop vac to get all lint cleaned out. I'm glad he did have to take the drum out after I realized the gasket on the exhaust pipe wasn't fitted on properly. There was some lint where there should not have been. Now that everything is clean and we have the new heating element installed we are good to go! The whole process of taking apart, installation and putting back together took about an hour and 15 minutes so not bad and we only had to pay for the part and shipping! Thanks PartSelect!

no heat

  • Customer: John from East Haven CT
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
followed directions using websites for diagnosis, repair, and part identifications. Take pictures of anything you take apart using your phone or camera. Careful of sharp dryer cabinet edges. http://www.partselect.ca/MultiModels.aspx?ModelNum=feq332es&searchTerm=img_R5D0195I&RefineSearch=0&imgMfg=Frigidaire&Page=2 http://www.applianceaid.com/test_with_ohmmeter.html http://www.applianceaid.com/ww-and-mc.html#e-noheat http://www.applianceaid.com/wwf-howto.html

no heat but otherwise ran fine

  • Customer: Bryan from Somerville MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I used the posts on the site to ascertain the problem (fuze or element burnt out). The pictures were very helpful. I pulled the dryer to the floor and using my meter checked both the fuze and the element. The electrical diagrams were very helpful also. I took the dryer apart further to make sure the coil was indeed the problem. I then ordered the part!

The drum was out of balance

  • Customer: Jamison from clayton GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 2 people found this instruction helpful
I removed the panel's that enclosed the drum, removed the drum and cleaned all the lint around the drum, heat panel, drive motor, and switch's.
removed the old support bearing and grounding ball then applied grease into the new support hub and reinstalled the new hub and grounding ball and then reassembled the dryer. Runs like it was new.

Loud Noise in dryer

  • Customer: Natalie from Jasper TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
Removed the top and front of dryer. Removed the old bearing and held the new bearing in place while my husband tightened the bearing into place......easy......now the dryer runs quiet again.

rear bearing failure

  • Customer: william from cherry hill NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 2 people found this instruction helpful
after cutting the power, I used a putty knife to release the two holding clips ot remove the top,, 2 foward facing screws on either side of the front and two cap covered screws holding the bottom and unhooked the two electricial connections for the control panel and removed the front panel. Since this was a stack unit and in a closet most work had to be done from the front. By reaching inside to remove the belt from the motor,removing the drum was the easy part, to get to the bearing, but unfortunatly I had to remove the dryer from the closet to replace the back bearing clip and ball. After that replacing the bearing bracket and housing it was a breeze. Getting the unit back in the closet was a slight struggle, but it all worked out for the best got a chance to cleas behind the dryer, and the repaire was successful, phew.

noisy

  • Customer: John from OFallon IL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 3 people found this instruction helpful
removed drum & replaced bearing, belt & shaft - reassembled

strike broken

  • Customer: Linda from Batesburg SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 9 people found this instruction helpful
popped in one in

lint filter bent

  • Customer: Ellen from Baltimore MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 19 of 222 people found this instruction helpful
Vacuumed lint and inserted new filter.
All Instructions for the GLEQ2152ES0
151-165 of 298