Models > GLEQ2152ES0 > Instructions

GLEQ2152ES0 Frigidaire Dryer - Instructions

All installation instructions for GLEQ2152ES0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GLEQ2152ES0
181-195 of 313
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Started with an annoying squeaking noise until the shaft broke and the drum hit the floor, KTHUD!!

  • Customer: Cheryl from Tulare CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered the rear drum assembly on Monday evening and the part came on Wed at 11 am. I started the repair at 1 and finished at 3. It would have been faster, but my computer kept freezing during the repair video. The video was so easy to follow. I could have used longer arms or a helper, but I managed to get the job done by myself. Needless to say, my husband was thrilled. Great service. Thanks

Heating but drum not turning

  • Customer: Richard from New Orleans LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
With drum not turning, I removed rear access panel and confirmed that the belt was missing from the motor pulley. The instructional video provided by PS was extremely helpful. It made the job simple. Removal of drum thru front frame was the most difficult part which was relatively easy. Once the front panel and drum were removed, I could then see that the front drum top glide nylon/felt strip needed replacing which I then obtained.

Rear bearing was squeaking

  • Customer: Robin from Lafayette OR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Repair went just according to the video except to pull the drum out there was a plastic lock at the front of the dryer. It was held in by one screw and easy to take off. When I pulled the drum out the armature and spring that hold the belt tight fell off. I panicked a little, but easily put the pieces back in place. When I started the dryer for the first time it sounded odd but realized it was the sound of all the grease spreading itself around the bearing.

Broken handle

  • Customer: Janet from South Dartmouth MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
EASiER than pie! Took off broken part, screwed on new part! Voila! Done. As good as new.

Washer Handle Broken

  • Customer: Jeff from San Angelo TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Washer handle fixed!

Dryer would not start at all

  • Customer: Todd from Mooresville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Used wiring diagram in back of machine control head. UNPLUG DRYER! Removed panel off control head and motor access cover at bottom of dryer. Tested door switch continuity first, then continuity from control timer to motor. Found open circuit on white wire. Opened top of machine (pops up at front) and found thermal limiter on back of machine was burned and caused open circuit. It's a little awkward to get to the screws with the drum in place. Use a 30º angle ratching 1/4" ratchet wrench with a magnetic #2 phillips bit.

drum would not turn

  • Customer: Paula from Tryon NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Opened top and screwed the front off. Put belt around drum. It took two times as my sweet husband put the belt on backwards the first time.

The door safety or something needed replaced.

  • Customer: jane from blairsville GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I called a wonderful friend who diagnosed the problem; ordered the repair part; and fixed it!!!

My dryer was squealing, which we ignored for awhile, then the dryer was beginning to have trouble turning.

  • Customer: Jennifer from Cincinnati OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video on your site which was very helpful and informative. The one thing that proved to be more difficult than it appeared in the video was reengaging the belt. Every time we tried to do it in the way the video showed, the tensioner arm would come off. The belt was very tight, even with that arm pulled back. We ended up just putting the drum part way in and then putting the belt on the arm and motor, and then stretching it over the drum. Perhaps because it was new, it was so tight. The rest was a breeze. Just followed the video. Was quoted $310 for this repair and I did it for $40! Thanks for your help and website! What a break in a terrible economy. You helped us out!

Broken drive belt

  • Customer: Thomas from Woodland ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Raised the lid, removed 2 little screws,slipped the front panel off, disconnected the safety switch, vacuumed everything, slipped on the drive belt and reversed my way out. It was way more easy than filling a grease gun!

Broken belt

  • Customer: John from Minot ND
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove drum, replace belt, return drum

Cut belt

  • Customer: gary from little torch key FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the vidio from yor web site it was great without it i would still be trying to get done.

Dryer was not drying completly.

  • Customer: Scott from Otsego MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the Control Thermistor (part # PS1149368) by removing the two screws on the bottom of the lower panel below the door. You will see the Control Thermistor just below and to the left of the discharge chute. Remove the two screws holding the Control Thermistor in place. Disconnect the two wire and reconnect to new Control Thermistor. Replace screws in reverse order of above.

Dryer element burned out

  • Customer: Robert from Gatlinburg TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First I watched the video available on the web site. After watching the video, I knew exactly what to do and how to do it. Really made the job a lot easier than it would have been. Some steps were harder to do than the video made them look but I atribute a lot of that to the fact that they were working in a large work shop and I was working in an area not a lot larger than the dryer. The hardest part of the job had nothing to do with changing the element, it dealt more with getting the vent hose off and on. Who ever designed the connection apparartus on dryers, used to connect that stupid hose to the back of it, must know something I don't. I have never had any luck when it comes to being able to get the hose connected and then getting the dryer back in the hole it came out of, without the hose falling off or getting crimped. PartSelect is a great company to deal with. Ordering was easy due to the highly intuitive web site and I got the part in two days. Saved me a lot of time running around town, burning a bunch of gas trying to find find what I needed. Thanks

Door handle top mounting bracket on dryer door busted

  • Customer: Jon Henry from Seabrook TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy fix. Removed remaining bottom mounting screw and removed old door handle. Positioned new handle on dryer making sure it fit properly in it's slots and installed screws into mounting brackets. Worked perfectly.
All Instructions for the GLEQ2152ES0
181-195 of 313