GGE350LWB00 Whirlpool Range - Instructions

Ordered the part from your company. It arrived promptly. Gave to to my two sons 22 & 29. They fixed it.

Very easy........................................

removed screws and disconnected the wires removed element and did the replacement less than 15 minutes, and cost less than locally by 25.00 and received part the next day. EXCELLENT

When the element failed, it continued to glow nearly white-hot and slowly burned along a spiral path on the element. I figured this MUST be due to a voltage leak - the control was OFF on the range.

I shut off the breaker, removed the two screws where the element goes through the back of the oven, pulled the element forward and pulled the wires off of the element. (Found it handy to twist the wire connectors outward to prevent the wires from slipping through the back of the oven.)

A new element won't "fit" exactly but you can easily push it into position to get the screw holes to line up. Total time was less than 15 minutes.

Our Maytag electric range has a small oven on top that doubles as a toaster, and food warmer. The lower one is a big oven suitable for Thanksgiving Turkey Etc. It is also a broiler as is the top oven. The top one had the bottom element burn out about 5 months back as well. Now the bottom element on the lower oven had burned out as well. The oven has some age on it, but when I looked to replace it I saw it would be approx $1800.00 - $2000.00 for a new one. I knew the elements were replacable and thought if I should call out the lonely guy, the Maytag repairman. Nope, I pulled the stove out disconnected the 220 power supply. I got the Model number off the back stamped info plate. I looked up Maytags parts on Google and the first one was PartSelect.com. They have easy fill-in spaces for Model and Make and a schematic of the oven and all it's pieces are visually displayed. I found the part I needed and ordered. It arrived in two days, very reasonable, very fast shipping. Pulling out the old elements required only a battery operated screw driver, a flash light, and a magnetic dish to keep track of the screws.The removal of the rear panel takes about 10 sheet metal screws. I marked the leads I disconnected by color with a felt tip pen on the back. I disconnected and removed the aforementioned clips, cleaned inside the oven and placed the new element in, reconnected everything on the back as it had been according to my color assignments, replaced the back with battery operated screwdriver from the magnetic dish, reconnected the 220V power supply. Done, in about 30 minutes; I saved a bunch over a new Stove and at least a couple hundred over a service call. Easy and satisfying.

Real easy, I removed the two screws holding the element in place, then pulled the element out a few inches to reveal the wire connectors. pulled the connectors from the old element and then replaced with the new one and screwed it back into place and presto! All done and cooking again. The replacement part came in 2 days fast and reliable. Thanks PartSelect.com

Turned OFF the circuit breaker. Unscrewed the old and screwed in the new. Very easy. There were helpful hints from other people on the web site, ie. turn off the circuit breaker first.

Put a new one in.

I watched the video you provide and it answered all my questions. You estimate repair at 10 minutes. My wife said I waz done in under 10 minutes Watch the video, it explained every step and all the little tricks to the snap connections.

unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!

Power turned off. Door of the oven lifted off. Four screws removed, old element pulled out to reveal electrical connectors. Wires easily removed, and element discarded. New element connected to the two conductors, four screws installed and the job was completed.
Very easy. Took about 10 minutes.

Easier than making a pie! Unscrewed 4 screws and detached the element from the back of the small upper oven. Connected the new element and put the 4 screws back in place. We saved $129 service fee by doing this ourselves not to mention the markup on parts. Shipping was very quick! While I hope to not have to do this again...I would do it again in a split second!

swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. Used the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.