All Installation Instructions for General Electric Dishwasher GDWT360R10SS

drain pipe was missing when purchased used dishwasher

oversized outlet not available in local stores, this one fit perfectly

Parts Used:

Drain Tube Kit

arthur from ALMENA, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bottom dish rack would not roll in and out because several wheels were off because of broken axles. It had to be lifted to get in and out which resulted in many chipped and broken dishes.

I removed the bottom rack from dishwasher. Took off the wheels with the broken axles. Put the new axles on the new wheels and slipped them on the rack. They fit perfectly and rack now glides in and out smoothly. Easy as pie, and took less than 10 minutes. Parts arrived in just two days. Thanks for the great service.

Parts Used:

Dishrack Rollers and Axles - Kit of 8

Darrell from WAHPETON, ND
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Valve leaked

Turn off power and water from dishwasher. Remove Base Access Panel. Remove the upper 2 screws that holds the dishwasher in place. Pull out dishwasher. Locate the valve and remove the 2 screws holding the mounting bracket. (I used a hex Nutdriver to remove the screws) Remove the valve. Disconnect the wire connector. Disconnect water supply. (Place a towel to catch the water) Loosen the hose clamp holding the inlet hose and remove the hose. (I used pliers to loosen the clamp) Remove the elbow from the old valve and reattach to the new valve. (Use teflon tape around the threads) Reverse the Process. Check for leaks. Piece of Cake. Part was an exact fit.

Parts Used:

Water Inlet Valve

Thomas from LAS VEGAS, NV
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Wrench (Adjustable)

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The lower dishrack connectors on the original roller axle parts had loosened so the rollers kept falling off

1. assemble each of the new rollers and axles by inserting the axle through the roller from the back side; push until the two parts snap together; 2. remove the cutlery basket, take the lower dishrack out of the dishwasher and turn it upside down; 3. remove the old rollers from the dishrack and send them for recycling; 4. push each roller on the corresponding wire shaft of the dishrack, with the axle connector arm against the vertical part of the shaft, pushing the roller assembly against the shaft until it snaps together. NOTE: the new rollers are wider than the originals and fit snugly on the tracks; no wobbling; the connector snaps are an improved design that should last as long as the dishwasher.

Parts Used:

Dishrack Rollers and Axles - Kit of 8

DONALD from PORTLAND, ME
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Wheels and axles on bottom dishwasher rack broke.

Put them on and snapped them in. No problem!!!!

Parts Used:

Dishrack Rollers and Axles - Kit of 8

Joan from FREEPORT, ME
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Loud noise during the drying cycle at end of wash.

Power off. Loosen screws under door with door closed. Open door, remove Philips screws, slide off door. Remove and replace motor. Note: the motor I replaced had identical resistance readings as the new one but was still bad. The old motor can also be disconnected and powered from a 110v outlet in ur house. Under the kickplate I found a folded up paper with an electrical diagram and the function test to test individual motors and pumps.

Parts Used:

Blower Motor

Edward from ALEXANDRIA, VA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Wheels on lower rack failed

Install the axel in wheel then push onto rack

Parts Used:

Dishrack Rollers and Axles - Kit of 8

Wayne from DUMFRIES, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Water leak under Unit

Remove Base Access Panel; Removed Valve Mounting Bracket & Valve; Disconnected Wire Connector; Disconnected Supply Line & distribution Hose; Reversed the Process. Piece of Cake; Part was O.E.M.Component Exact Fit; Took Longer to Write this than it took for Fix. Thanks I Will Be Back for other Parts.!

Parts Used:

Water Inlet Valve

GEORGE from LEVITTOWN, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

8 of 16 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

old part leaked

unscrewed dishwasher from cabinet, then I flipped dishwasher on it's side. loosen pump motor bracket arm on the end of the motor. loosen pump motor to pump conecter hose clamp and then unscrewed pump motor connector from dishwasher. To install I did the reverse. very easy.

Parts Used:

Pump Connector

robert from east windsor, CT
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

latch on detergent assembly broken off

Easy repair-removed hex nuts and and screws to pop out old part and replace with new one. New part works better than the original! 1st replacement part arrived with a broken piece, a quick, courteous phone call got a replacement sent out. It took a 2nd phone call to obtain the refund, but the customer care reps are efficient and friendly. I would order from them again for positive service reasons alone.

Parts Used:

Detergent Dispenser with Rinse Cap

Carri from Louisville, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replaced a badly worn & torn Gasket

No tools required. The seal just pushes into a channel around the tub. The lower ends are held by a wire that spans the lower edge of the door. The center of the gasket is marked to agree the the tub center.l. The seal just pulls out so I removed it and the wire. Cleaned the seal channel and wire and installed the new seal starting at the Top center and working down to. the lower ends are anchored,I found the center of the seal and upper channel and pushed it in place and worked around the corners and down. It took longer to clean the channel and door than to install the gasket.

Parts Used: