259530-3-M-GE-WD18X10010-Pump-Connector.jpg
259530-3-S-GE-WD18X10010-Pump-Connector.jpg 259530-1-S-GE-WD18X10010-Pump-Connector.jpg 259530-2-S-GE-WD18X10010-Pump-Connector.jpg

Pump Connector

PartSelect Number PS259530

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Leaking water.
  • Compare At

    $23.05
  • You Save

    $3.84
  • Your Price

    $19.21
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

CLAMP

Part Number 258119

This clamps the drain pump port to the sump inlet port to hold it in place.

$3.76
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.0 / 5.0, 5 reviews What's this?
1-5 of 5
 

13 of 16 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)

CustomerAshraf from Merrick NY

Leak from the bottom center

The connector pump had a pinhole leak at the seam (new part did not have seams). Also replaced the sump inlet which looked worn and the impeller.

Lay dishwasher on it's back to access the bottom. Loosen all clamps. Remove both U shaped holders on the sump inlet. Remove screws holding the drain motor. Pull out the pump motor and sump inlet. Connector pump can be unscrewed from the bottom.

Replace parts and reassemble. It isn't that bad once you start disassembly, especially for anyone somewhat handy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Pump Connector

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

Customerrobert from east windsor CT

Old part leaked

unscrewed dishwasher from cabinet, then I flipped dishwasher on it's side. loosen pump motor bracket arm on the end of the motor. loosen pump motor to pump conecter hose clamp and then unscrewed pump motor connector from dishwasher. To install I did the reverse. very easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Pump Connector

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerJim K from Whittier CA

Pump connector leaking

Open dishwasher and remove the bottom spray wheel, filter, and unscrew the mounting bracket to release the pump connector below the bottom of the unit. Remove mounting screws at top front of dishwasher and carefully slide the unit out; you may have to pry side panels inward with a flat screwdriver in order to get the dishwasher past any cabinetry. Be careful not to pull the dishwasher too far out as the water supply and drain hoses could be damaged. Unplug the unit. Turn unit sideways and tip over onto its' back. At this point, the sump will have to be removed using a nut-driver and/or socket set. This will open access to remove the old pump connector. Replace the old connector with the new connector, and reassemble the sump, connecting and firmly tightening all connectors. Tip unit upright. Screw mounting bracket back into the bottom of the dishwasher and put the remaining parts back. Before pushing the unit back into it's nook, I advise running a quick cycle just to make sure there is no leakage. If there is no leakage, put the unit back, tighten the mounting screws and you're done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 10 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerSAMUEL from DUNCANNON PA

Water leak from under dishwasher. Leaky inlet sump

Disconnected the electricity, the drain hose, and the water supply from the dishwasher. Loosened the two screws from the countertop and pulled out the dishwasher. Turned it on to it's side. Saw the damaged inlet sump. Had to remove the Pump connector to get to the inlet sump. Checked it also and discovered that it was starting to develop a small crack from the inside. I decided to replace it as well. The job involves removing the hose clamps and removing the spray mechanizm from the interior of the dishwasher to spin out the inlet sump. Not a difficult job.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:More than 2 hours

ToolsSocket set

Customerwilliam from sykesville MD

Water leaking from sump

I had a slow leak from vicinity of sump. I replaced sump and pump connector as these were only likely sources of leak based on parts select history. Turns out plastic tub had a fine crack. The crack was directly under the heating element which had melted the plastic and over time created this small crack that was found by a repair guy immediately. I even suspected a tub leak and searched for one but being directly under the element made it invisible to me and in an area I did not suspect (front). Oh well - also learned GE charges $100. to come to my house, show me a crack, and leave (I repaired it with epoxy).

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5