GD5PHAXMS10 Whirlpool Refrigerator - Instructions

Toughtoget the ta b into the paddle but once in it was ok.

Just replaced the old Push-On Start Relay and it started to work again.

my Husband took the part off.unscrewed some screws took the front off put the new part on the front put it in and awhile later ice.It takes awhile for ice to start.so don't worry.Don't call a repair man do it your self and save the service call money.I ordered this part in the morning got it the next morning.Don't know if they have a place near Jax.FL.or not anyway i was very impressed.And very satisfied and saved a little bit of money.Iwill use them again.And will tell my friends Keep up the good work.MaryLux.Jacksonville,Florida.

I removed the door and switched out the cams on the bottom. Super easy. Door closes perfectly now.

i talked to a gentlman name Ruben and directed me to the parts i needed i ordered them and put them by myself i ended up saving over 200.00 dollars thanks to Select parts the minute i finished the process and closed the freezer doors i could hear the ice is comin down again it was good feeling. After i changed the emitter and the receiver this year every thing is working again

My name is Tuan Nguyen. I have no ice and no water dispense into icemaker tray. I replace the the icemaker control and motor assembly. I unscrew a screw underneath the icemaker unit and disconnect the wire clip and pull out the icemaker assembly. I remover 3 screw from the motor assembly unit and replaced it with the new motor assembly. and installed the unit back in the compartment. It took about twenty min. It make me look good, that my wife knows i can fixed the problem without calling the repair men.

empty frezzer take door off unplug wires going to ice maker unscrew/bolt icemaker replace door take motor cover off ice maker remove screws on motor replace ice cup and put every thing back together

unplug freg.took everything out.pulled out shelves and pulled out back panel.their was my part i had to replace.

The comments from PartSelect were 50/50 that it would be the motor on the icemaker. We bought the motor which came 4 days leter and followed the installation instructions in the video. We started getting ice about 2 hours after the installation!

Turn the unit OFF - Removed one hex head screw on the bottom of the ice maker, removed the cable cover and unplugged. Removed front cover & Slide the icemaker out. Removed control cover and removed the three phillips head screws to the controller. Put the new controller back on with the three phillips head screws, pushed the cover back over the controller. Plugged the unit back in, then slide it back in the tracks, put the cable cover back on and installed the hex head screw, popped the front cover back on and turned the unit ON - DONE!

My dad and I worked together. The video helped but it was a little more complicated. If you can't find the water supply, remove the filter and water should stop, that's what we did. We had to remove the freezer door for access to the ice maker. It was tricky taking the icemaker off and getting it back on. Replacing the motor was easy, just as shown in the video. Just like others have said, within an hour of the repair the ice starting coming!

Replaced the Electronic control boards first, emitter and receiver, and that did not fix the problem. I then order the Control board/motor assembly in the ice maker, this did fix the problem and after a couple of hours I had ice. The repair was easy and the videos on the web site show you step by step.

Thanks to this site, it told me what was wrong, what to order and how to repair it.

Shut off the water supply. Removed the water line and filter housing. Had to watch the how to video to figure out how to disconnect the lines form the housing. Removed and replaced.

Remove front dust grill at bottom, pulls off with a little muscle.. While this is I found it to be a good time to vacuum area. Remove two screws at bottom in front with nut driver. Lift wire on left out. Hold filter unit and grasp water line and pull steadily repeat for other line. Remove old filter housing and reassemble. The worst was having to buy the whole part just for the keeper.