FDB1502RGM4 Frigidaire Dishwasher - Instructions

Unscrewed the old spray arm and replace with the new spray arm.

The best part was in the ordering process. Having the diagrams with the parts let me see that I was ordering the correct part. Thanks!

Unscrewed upper sprayer by hand, screwed new one in by hand. Piece of cake!

The spray arm comes off into 3 parts but is really only supposed to be one. I removed the nut from the old assembly and attempted to place the new assembly on by hand. The new nut seemed to be slightly smaller than the original so it would not attach to the dishwasher. Using a kitchen knife, I removed the new nut from the arm unit and attached the new arm to the original nut and it went back on easily. The connection of the new arm to the new nut was 3 tabs that needed to be depressed with the knife and was a different conection method than the assembly that kept coming off in the wash cycle. The replacement part had a much better design than the original.

I replaced the basket. No tools necessary. New basket seems sturdier than original. Very satisfied with my purchase.

Unscrewed dishwasher from cabinet and pulled out about 1 foot. Took bottom plate off of dishwasher. Undid clamp on hose of discharge of inlet water valve and removed hose. Shut off water to water inlet valve and removed. Took wiring clip off of water inlet valve. Removed 2 screws holding water inlet valve in place. Installed new water inlet valve in reverse order.

Removed the bottom panel on the unit (2 screws hold it on) and pulled the dishwasher out about 4"--after turning off electricity to the unit. Removed the broken spring and the old linkage and replaced them with the new parts. Pushed the diswasher back into place, and replaced the bottom panel. Turned on the electricity and the diswasher door is "good as new." This is quite simple to do; just takes patience.

I installed the new spray arm without any tools and it worked perfectly.

Discovered upper wash arm had come off. It looked like it was repairable, but the bushing/clip holding the arm came off after one wash. Looked on line and reviewed part and saw it was a one piece assembly from photos. Removed old assembly by unscrewing from top of washer and screwed new assembly in place.

I removed the dishwasher from the cabinet space (two screws) and manually replaced both springs. I replaced one spring first to see if there would be an improvement when the second new spring was installed. There was much better tension once the second new spring was added.That is why changing both springs is recommended. This was very easy.
Changing the gasket was scary because I thought the the whole door would have to be taken apart. You know nothing ever goes back together the same. I feared that I would create an even bigger leak than what I had. Taken the door apart didnt work for me, so I just pulled the old gasket by hand and pressed in the new one. I made sure that it was seated correctly. Voila no leak.
The dishwasher is running as good as new.
I ordered these parts on Friday morning. They were on my door step Monday morning,
I highly recommend ordering from this site.

Fully open dishwasher door to horizontal position, remove lower dishwasher rack and relocate to another temp location, grab old lower door seal from right or left corner and pull completely out of door, lay the old bottom seal aside facing the same direction as once installed (seal has a notched side which faces the right side of door), match direction of the new seal with the old seal (match the notched side of seal to the right side of door), gently push the seal into the door starting on the right side (notched side of seal fits tightly into a receiving area inside the door), and finally push the remaining portion of the seal into door (aligning with the right side already properly seated inside dishwasher door). Close dishwasher and run water cycle to confirm leak.

I removed the old spray arm by pulling it off of the base then I pushed the new one on and made sure it was on properly then I pit the base back into the dishwasher and it was good as new!

I was able to pull out the top basket were the glasses are put then I lined up the back and the center plastic clip an slid on the center spray arm. It took about 2 miniutes

All I had to do was take out old racks and replace with new ones. However the top rack did require taking off the part where the water runs through, it was easy though.

I would like to comment on how quickly and efficiently the parts arrived. I placed my order on a monday morning and am pleased to report by tuesday afternoon they arrived, much to my delight.

The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job

tossed the old one a replaced with a new.Hardest 10 second repair ever....It took 10 seconds had to open and close the door.