Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bottom spinner wouldn't stay on
VERY simple---unscrewed three screws on the broken part (the little nubs that held on the bottom spinner were broken off), screwed the new one back in, re-attached the spinner.
I was VERY pleased with the customer service and quick shipping (ordered on Sunday night, the part was delivered Wednesday morning). I would definitely recommend this site to anyone, and would use it again. Five Stars!!!!
Used pliers to remove old seal. Keep seal in position, note the notch facing the hole. Align the new seal, press it in, the notch helps align. Mine slipped in easy
After moving the dishwasher out from the cabinetry, I removed the screws holding the pump in place. Pulling the pump from the formed plastic opening, I found a toothpick lodged in the pump housing. At the same time I noticed that the front o-ring was deformed due to being the incorrect size (too large). It was installed at the factory this way.
I went online to search for new parts. PartSelect was the second or third listing on the search page. I submitted the dishwasher model number and was taken to a set of parts illustrations. I was easily able to find the o-rings I needed.
Removed the bottom panel, and I had to disconnect the water supply, which did NOT use flexible tubing (much to my disappointment), removed the screws holding the diswasher in the cabinet. Slid it out, took the old springs off, put the new ones on.
the rack had broken on one of the arms that connect to the wheel in the slider
I unclipped the plastic pieces at the front of the rack. This was very easy. Then I removed the old rack. I then removed the water sprayer from the old rack and placed it on the new rack. This was simple and I unscrewed the water sprayer by hand and snapped out. Putting it on the new assembly was very easy. Then I placed the new rack on the two stainless steel sliders and refastened the plastic clips at the ends. It was no problem.
First point of leakage was the door. Turns out that a gasket at the bottom of the door functions as a wave trap. As the bottom sprayer spins it sprays against the door and creates a small wave of water this gasket was starting to disintegrate, it was letting water surge over the small tray at the doors bottom. Easy to replace just pull down and remove press fit on inside door bottom. Only when this was replaced did I find the real leak but not until I guessed at the tub seal as the leak. Very hard to see where the water really comes from! Turns out it was not the tub seal but a clip that holds the heater element got smashed down from a dropped dish rack at some earlier time and this caused the heat to increase at the clip and eventually heat the clip to extent it melted the tub directly under it. JB Weld to the rescue and we have a waterproof tub again. Well almost! The tub gasket resisted my best efforts to seat correctly and thus required a new tub gasket, still hard to seat but after 2-3 attempts we have a winner. Total cost about 50 bucks vs. 6-700 for a new unit. Wife is happy!!
Dishwasher not cleaning dishes, found it not filling with water because hose was ruptured
Turned off elecrtic and water to dishwasher and pulled dishwasher out from under cabinet. Removed broken hose using pliers to open hose clamps. installed new hose.
Ordered the parts, put into place and that was it...very easy...had to undo the upper rack spinner wash blade but was easy to remove and put back onto the new rack...
My daughter held the flashlight steady as a rock as I hooked not one, but two new hinges in place. Throughout the whole ordeal neither of us complained or lost our resolve. We conquered!
After shutting off power to the dishwasher, I removed the two screws holding the door cover on the inside of the door sides, about 8 inches from the bottom of the door. I slid the cover down and off, and unplugged the wires to the dispenser. Then I removed the six screws holding the dispenser in place, removed the old dispenser, installed the new one, replaced the six screws and plugged the wires back in. The door cover and the two screws was all that was left. It took about ten minutes. Easy.
Original hose needed replacement due to leaking holes
The replacement hose was not as long and the original and therefore did not fit into the track made for the original one. Though it was long enough to work, an additional 4 inches would have been an exact fit. As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better.
Old spray arm melted and clogged, had popped off once and laid against heat coil.
Popped off the old spray arm ... INTENTIONALLY, and put new one in. Had to lift off small strainer to allow old arm to release! Be sure to turn arm until it clicks into place, return small strainer/clip, and you are in business! Most trouble I had was getting this old bo y up off the floor afterward. Dished so much cleaner now!
1-2-3 snapped off the old and snapped on the new! New part was just as ordered and just like original! My dishwasher is like new again! Thanks PartSelect for your great price and prompt shipment!
The Inlet valve was leaking. I removed the old valve in less than 30 min.Note: need bright flashlight! It could have been quicker but I had to lie on the floor and squeeze my big hands under the opening (kick panel). Once I got the two small bolts out, I was able to manipulate the valve out from under the dishwasher, then I carefully removed the two lines. I received the part in 5 days and installed it in 45 minutes. It could have been a faster installation, however I was not about to pull out the whole dishwasher. Again, I was able to manipulate the new valve back in & tighten then test everything.(note: need a bright flashlight to see underneath) I immediately ran a load of dishes and Presto! No leaks and runs like a Swiss watch!