Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water valve was leaking
The u tube instructions were exactly what is needed. I had to cut off the old plastic pipes. My pipe had threaded connectors. Pex push on connection is super easy. You don't really need a block of wood to cut it if you have a sharp utility blade. If if you are sure this is the problem this is a really easy fix. Steps 1 turn off water at wall unplug electric also 2. Disc line at valve on refrigerator 3. Remove 2 screws holding valve 4. Pull valve out and remove plastic hoses and electric connections pay attention to color of pipe and electric connection. Mine were color coded. Had to cut off thread connectors. Reattach in reverse order or do one at a time. Check for leaks.
Freezer leaked, no water disp. & Crusher didnt crush
First I defrosted the entire unit, both sides for 24 hours. Restarted, I now have water dispensing. (It had apparently frozen) Next I took out the ice crushing part and took it apart, (a few screws) by removing the broken floppy piece; the small plastic floppy door that allows ice to crush, replaced this small piece, rather than replacing the entire big plastic piece that I ordered. Used a slot screw driver removed the old floppy piece that was broken and removed the same piece from the new one and switched them out. Reassembled the entire unit (a few screws), put the ice back in and it works great. I got the instructions for taking apart this from this site, however, it was fairly easy to figure out. Just be patient with the plastic parts.
Refridgerator too cold...freezing food,could not turn down
First,read "how to" on the internet because the thermostat comes with no instructions and unplug refer. Second, remove food and lower rear panel. Third, pull off thermostat from tube it clips to, unhook wire harness,and cut wires.Fourth,add heat shrink tubing from store(that supplied is way too big) and connect wires with automotive connectors;shrink-seal tubing with flame.Fifth, re-install everything, and replace food.Sixth,use a thermometer to check temp and adjust controls as needed.
We love our ice here. I seem to replace the ice makers one to two times a year. Generally the ice cycle gets off for some reason and it starts making loud popping/clicking noises (gear grinding). Its easy to replace. Simply loosen two screws holding the unit to inside of freezer and disconnecting the wiring harness. Unit slide up and out. Replacement is super easy (5 mins or less). Bam! Ice!
loosened 2 screws with 1/4 inch nut driver, disconnected electric connection lifted old ice maker out, replaced it with new one hooked up electric plug tightened 2 screws
Freezer was cooling, but refrigerator was not cooling all the time. Evaporator fan was running, so decided to try new thermostat.
Followed install instructions on utube. Once freezer was empty, back panel was easily removed, and defrost thermostat was in plain sight, and easy to replace. Hope that solved my problem. Refrigerator has been plugged in for four days now, and is cooling properly so far.
Unplug refrigerator , loosing two screws. Lift ice maker up to remove from position. Disconnect electrical connection. Reverse procedure to install new ice maker.
I first ordered the wrong switch I called and got a return label and was refunded my money before even shipping the wrong switch I was helped for the right switch and it arrived in 5 days the replacement works perfectly very easy to install. Thank you
removed ice maker storage holder and then remove two philip screws and unplugged four pin connector. removed ice maker and installed new one . very easy to do