EGR3001 General Electric Range - Instructions

After receiving the part ordered in one day, I removed the racks and the bottom flame spreader. The igniter assy. is held in by two screws, which only took a minute to remove. I removed the ceramic wire ties from, the old igniter and wire tied in the new one. Put everything back together and tested the oven. It works great again. Thanks for the quick response and delivery.

I removed the whole burner (3 screws) and the igniter (2 screws). IGNITER comes from Mfg. boxed with wrong plug on igniter - however they supply two porclean nuts so that the wires can be cut and joined. I recommend that you use the plug off the old igniter and splice it to the new part, so that it will plug into the stove's existing plug

First I removed the pan drawer. Then I removed the metal cover under the stove. Not sure if you have to remove that or not. I think I could have left that on. I then looked inside the oven and removed the two screws in the back to remove the lower cover. Ahh, the hot surface ignitor and flame grill exposed. I then turned on the oven again to make sure the hot surface ignitor was not glowing. I went back underneath, and disconnected the hot surface ignitor. I followed the wires from it to where it was connected. I then unscrewed the 2 screws that held the flame grill in place. Next, I went back in the oven and removed the flame grill with the hot surface ignitor still attached. I then unscrewed the hot surface ignitor and replace it with the new one. Key points: make sure you mark which wire had which connector, or only cut one at a time. Also, they do not come with new clips, so don't cut you wire too short. I then fed the wires and the base of the flame grill back down the slot, rescrewed the flame grill to the oven, attached the wires, and turned on the oven to make sure it worked. I finally replaced the lower plate inside the oven, the lower plate under the oven, put the drawer back in and I was done.

I ordered a new display from the internet. I removed the panel where the display is housed, unscrewed the entire display assembly and unplugged all wires connecting it. (I made a drawing and noted colors of wires) I removed adhesive face of display and replaced it on the new display. I then screwed in the display and reconnected the wires as per my notes. I reassembled the panel and applied power and it worked like new.

frist removed 4 screws from the side cover 2 screw from the front cover disconect 4screw that hold the part in discont the 4 wires

It was very easy I removed two screws unpluged the sensor and wire spliced it together and also replaced the modual on the top of the stove and it was that easy.

First I removed the oven door handle from the inside by removing the 2 screws. The screws have standard hex heads. You need to be careful you don't strip them. Once you remove the 2 screws for the handle the outside frame for the door will come away from the oven. You then need to remove the frame by unscrewing 2 screws at both the bottom left and bottom right corners of the door. Once you remove these, the exterior door frame will come away from the oven. The replacement glass actually sits on the outside of the frame. You simple need to slide it up into the top edge of frame. There are little grooves that hold it at the top. Once you have it in place, slide the bottom edge of the glass into the grooves on the bottom of the front door. Replace the 2 screws at the bottom right and left corner and then tighten the screws for the handle on the inside of the oven door and you're done. Pretty simple really.

Take out inside of oven.Igniter is held on with 2screws and electrical clip.take off old one and put on new one.

Hi temp (900 deg) engine gasket adhesive on numbs and press in. DONE !

It all began one find night baking and suddenly the oven would not light up. And so for the next few years all I ever used the stove for was for stove top cooking, See Im a single guy so its not in my nature to get to fancy when it comes to cooking home meals,but after a while the mood changes and you finally get up the motivation to fix whats wrong. The change over went easy,easier than I expected.And the part worked just fine. As far as ease of the order and receipt,couldnt have been better,I got the part within 48hrs and that is fast! Thanks to all.
T.Melillo

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

Disconnect power. Remove oven door, oven racks, bottom pan, drawer below the oven. unsnap igniter wire connector. Remove two screws holding the igniter in place, remove igniter.

Install igniter (placing igniter wires away from any heat producing parts) and all parts in reverse order as they were removed.

Oven heats good now, makes great cornbread and biscuits, the wife helps the oven do this.

Repair was quite easy. Remove four screws and lay back sheet metal panel. Transfer wires from one module to the other and then put new module in place. replaced the sheetmetal panel. Spark now presen at all burners. One small thing worth mentioning. Each burner has a gas distrubution cap and that cap has a small hole to the spark cavity. One of these was pluged with grease and that kept the burner from lighting until this hole was cleared.

Removed the old caps, replaced them with the new ones.