EDW2060F02SS General Electric Dishwasher - Instructions

At first, I found a metal band that was rusted and loose, replaced it but still had a leak. I went to the diagnosis section and identified another area of problem, ordered the part and got super quick delivery. With the help my wife I was able to pull apart, repair and get the unit to run and stay dry. Wife is happy because she loves the décor of our old but now dry dishwasher.

within 5 minutes.Great site for information and parts

The repair went really smoothly, I found a video on youtube for how to remove the dishwasher, and the video on the parts page did a great job covering replacing the motor. The repair went really well. As others have noted, it ran really nosily the 1st time, and a little the 2nd. After that, it ran quieter, and stronger than it has in the 4 years we have owned the house.

I thought to myself, this is going to be easy, but I hit a couple bumps getting the end caps off. I just watched the video and it was great and helped me be sucessful. The only thing that would have helped was instructions on how to put the end caps back on! david

Removed the tray from its rails. Removed axle clips fro tray and replaced with new axles. Put tray back in rails and I was done. Works like

Followed the video on this site, replaced part in under 10 minutes, ran a cycle - p-e-r-f-e-c-t !!! Thank you so much - I am sooooo not a diy type person, but this was easy!

It was amazingly easy repair. I just order the correct parts from “PartSelect” and installed them and done. It was fixed.

Laid dishwasher on its side to get to the bottom very easily, unscrew the screw that was holding the bottom of the hose to the dishwasher, then remove the 2 screws in the top of dishwasher that is holding the shower hose in placeinstall new hose in reverse, very easy .

Ordered parts from Parts Select, and replaced lower roller wheels. The diagrams/ drawings were key in ordering the correct replacement parts - thanks

The three top mounting points broke from the control panel that fasten it to the door assembly. Vent assembly mounting point also snapped. All occurred when movers tried moving the dishwasher by the control panel handle. Removed the nine screws from the control panel (six door frame and three already broken top mounting points). Position the door lock swing arm to the middle of its left/right travel, and remove the rear panel to expose the inner door. Disconnect electricity. Even though the washer is off, 110 is present at the door. Using the new control panel as a guide locate all the mounting points (screws) for the control board, sequencer, and vent control. Be careful to note the how the lever control is mounted that is located under the sequencer. Pull black and white connectors from the control board and any other connectors that interfere with the removal of the control panel. Remove control panel and reverse the order for assembly. NOTE the insert escutcheon #902 (name plate) couldn't be found anywhere, can be removed from the old control panel and reused. Very carefully working from the bottom of the name plate use your fingernail (not a sharp object) and start to work the plate loose from the control panel. Work to the end without the brand name until you loosen that end. Slowly pull up at a 45 deg angle and it will slowly come loose. Be patient. They use a sticky rubberized glue. Good luck!

In the video, they must have been removing new parts from a new machine. 7 year old parts do not come off so easily. You may need a screw driver (I used a plain old dinner knife) to pry up the prong. (Parts went flying as they broke off for good!) I had to use a wrench to get the roller off. BUT, the new part slipped on like "greased lightening." Sooooooo, watch the video, follow their step by step instructions, but be prepared with a tool or 2 since the only reason you are doing this is because it is OLD!!!

Pop the new wheels on. The rear wheels are thinner than the front wheels so rack slides in smoothly

Watched the video, replaced the recommended part EASY-Done Would not hesitate on any other appliance repairs in the future Great site!

After examining the lower baffles, it was evident that their grooves were bent out of shape and warn. They were simple to pop out, I cleaned the area and popped in the new baffles. Unfortunately, the leak still happened. Upon further examination, the corners of the gaskets where they rubbed against the baffles also looked worn. So I ordered a replacement gasket and gasket insert and just installed them. Problem solved. The instructional videos were exceptionally clear. I'm not particularly handy. If I had not seen the videos online before ordering the parts, I would have called a repair service and spent $150+ more.

I unscrewed the front of the door almost to the bottom hinges and removed the latch. Went on line and ordered a replacement. The replacement arrived in a couple days (yeh), was identical to the one I had removed. I could have used another hand but went ahead and replaced it myself. It worked perfectly and I screwed everything back in place. I'm a 73-year-old female, good at taking things apart but not always good at putting them back together but will try anything. Was elated that I could repair it and it actually worked. Great service from your company!