DWU9202AAB Maytag Dishwasher - Instructions

My original order was for the "Motor Gasket" in the bottom of the tub that just looked nasty. Not leaking. Replacing that was a little more complicated, but used another customer's recommendations and worked great. Ran an empty load to check for leaks and thats when we discovered that we had a leak on the side of the darn thing. So we ordered the "Injector Seal Ring. Got it in about 5 days and after installing, (2 seconds), we still had a leak! Soooo, ordered the "Water Inlet Injector". 5 days later, we have NO MORE LEAKS!!! I would STRONGLY suggest that anyone who has a leak at the Water Inlet, order a new Injector right along with the Seal Ring. The shipping and handling was WAY more than the price of the parts. I'm happy to say that my 10 year old dishwasher is running like a champ. Thank You.

1) Remove the lower dish rack.
2) Use towel to soak up any water in the dishwasher.
3) Remove the bottom plate on the dishwasher front.
4) Remove clamp from around the discharge hose. Some water will drain out so have towel handy.
5) Dishwasher will need to be pulled out from its built-in area in order to feed the old discharge hose out and the new one in. MAKE SURE THAT THERE IS ENOUGH PLAY IN THE ELECTRICAL WIRES AND THE INPUT WATER LINE TO THE DISHWASHER TO ALLOW IT TO BE PULLED OUT.
6) Loosen, all the way, the white plastic locking arm that clamps the pump housing. It clamps on a white corrugated plastic piece.
7) Remove the spindle arm inside the washer by unscrewing the "tower" piece.
8) Remove the screws from the pump housing on the inside of the washer.
9) Lift the pump housing carefully and remove the rubber gasket from around the housing. There is enough play to remove the gasket and put the new one on.
10) Clean the area around the housing so that the new gasket seats properly.
11) The new gasket will have to be installed before re-installing the discharge hose.
12) Re-install screws in pump housing.
13) Re-install the spindle arm.
14) Tighten the white plastic locking arm underneath the washer that locks down the pump housing.
15) The new discharge hose can now be reconnected between the sink drain and the dishwasher.
16) Dishwasher can now be put back into its place.
17) Before closing up the bottom plate of the dishwasher, it should be run and checked for leaks before finally closing up. My advice - let it stand overnight before checking for leaks. after running.

Figured out that the only thing that could be causing this was a bad inlet valve. Repair was really easy. Didn't even have to pull machine out from under cabinet. First removed kick plate. Then placed towel under the old valve. Undid the power connections and water lines (in and out). removed the to screws holding the valve to the body of the washer. With the valve free, removed the brass elbow and installed it on the new valve. Reinstalled the valve and all connections. Works like a charm.

Took the replacment rack out of the box and found that it was the proper one. Had to rotate out the water director tower from the orignal rack and install it in new rack which took a few seconds to figure out . it was time to discard the ailing rack! Apparently the dish soap can attack the rack materia if there is any metal exposed and rot it out like rust so when this happens time for a new one. Otherwise there are no pins to support the bowls and plates in the lower section.

Simply remove the washer nut,then pull the float assembly. As far the lever,just unscrew the screw and replace the actuator lever. What was great about everything I was able to go to the presented diagram. This allowed me to find the exact parts I needed. Of course make sure you have the model number.

Our dishwasher got to the point where it would not complete a wash cycle. I found that by jiggling the door latch, the dishwasher would whir back to life. For awhile, if I put a clothespin on the door latch, somehow enough pressure would be put on the switch to keep the dishwasher going. Finally, the dishwasher refused to cooperate...so I ordered a replacement switch.

The repair was easy. I only had to remove the interior door panel, unscrew the metal bar at the top of the door and underneath the door panel, then remove the black plastic shield. After that, it was just a matter of wiggling the old switch out and wiggling the new switch.

CAUTION: Be very sure that the power to the dishwasher is turned off. I got a scare because I thought the circuit breaker was off, but I had flipped the wrong one and suddenly, with my fingers very close to the bare connectors, the dishwasher came back to life briefly. I ran downstairs and found the correct circuit breaker and all was fine after that.

Remove the Palnut Screw from bottom of Float assembly using pliers, Remove Pivot pin from Actuator lever w/ screw driver. Replace the Float , install new palnut Screw and re-install pivot pin on actuator lever.

That's it !!!!!!!!!!!!!!!!

I did not move the dishwasher out. It is a fairly tight space underneath, but the water inlet valve is located toward the front, so it wasn't too bad. The steps were:

1) unplug the power and turn off the water to the dishwasher.
2) remove the 2 wire connectors.
3) use the nutdriver to remove the 2 screws that hold the valve to the side of the dishwasher.
4) use a wrench (5/8") to remove the nut where the water goes into the valve. This takes some patience since you can't turn the wrench very far in the tight space.
5) remove the water outlet hose by using pliers to squeeze together the clamp and move it up the hose. Then twist the valve to free the hose and remove it from the valve. The nibs on the clamp are small and take a little time to get them squeezed together. If the hose has been on there a long time, you will have to twist the valve a few times to free it up.
6) now you will have to remove the sleeve that the nut was screwed onto. I had to take the valve to my vise to hold it. Then it wasn't too hard to remove.
7) use teflon tape before you reassemble. Just go in the reverse order.
8) hope there isn't a leak. Mine didn't.

The new water inlet valve seems to have fixed the problem!

Make sure dishwasher is powered off. Remove all inner door panel screws. Lift inner door panel upward and lean against the tub. Use a putty knife or spatula to lift old lower foam seal. Make sure door seal area is clean. Start at one end, butt new foam against the side of door and slowly pull glue strip backing while pressing foam down from left to right. Reverse door assembly.

Make sure dishwasher if off and door unlatched. Remove lower kick panel 4 screws and remove 1 screw securing float switch arm. Hold float stem with pliers and remove bottom stem nut. Remove float and re-install the new float with reverse procedure listed.
Super fast shipping on items!! Great service.

Peeled off the old foam strip, cleaned with rubbing alcohol, let dry completely, applied new foam strip,replaced door interior done I wish repairing relationships with fiance and kids were one tenth this easy.

The repair is fairly simple except that the diagram on the web site has an error - it reverses the positions of the long hinge pin and the short pin. I kept trying to do it as the diagram showed and of course it didn't work. Then I followed my instincts! The only other difficult part was figuring out which way to insert the spring but there are only a few options so trial and error was the simplest way.

Actual i missed diagnosed the leak and ordered a very expensive door gasket. The leak was coming from shrinage of the wax resevoire o rig and the tab seal for the soap dispensor. I missed the trees the forest got in the way. The leak was dripping alond the front panel well away from the main door seal.

I cleans a the plastic surfaces and noticed a lip around the opening for the reservoire and used 150 sandpaper to remove it. Replaced the O ring, tab seal and bothe selonoids and cleaned everything. Put it back together. Works find lasts along time

First I had to unhook the electric, water line and drain hose. Then slide out the dishwasher. Took several days to find the drain hose - local stores only carried a 6 ft hose and I needed a 7 ft. Once I found it online, purchased it and recieved it I put it all back together and all is good.

First of all, rather then spending the 44 dollars on the main door seal simply cut yours in halve and trim a quarter of an inch from the disintegrated ends and use superglue and glue these ends together. this glued end will now be up top and in the middle and new clean ends will be down in the corners. next I removed the plastic door panel using a torxhead screwdriver, I just stuck the new inner foam pad on the old one. Then I glued rubber washers to the inner frame about 1/8 thick in the top 2 corners only. Finally I reattached the plastic door being careful not to tighten the torx head bolts just tight enough. It's dry and working good.

We ordered the replacement part for our Maytag model and when it came we saw that it was different than the original part. The original part had 8 wheels with a higher left hand side. The replacement part had only 6 wheels and no higher side. The replacement part would not pull in and out evenly and was a bit too narrower. We called Parts Select and told them our problem and they are going to refund us in full and take back the part they sent. Alas we will have to buy a new dishwasher. We would use Part Select in the future for replacement parts.
Alice
Cambridge, MA