DLL3680SBLWW Hotpoint Dryer - Instructions

After removing the front panel with a 1/4" nut driver; I removed the drum, rear shield and spacer using a 3/8" ratchet, 6" extension and torx socket for the three drum screws. I then removed the 4 screws on the rear heat guard panel to get to the rear bearing assembly. I removed the rear bearing assembly and replaced the plastic bearing and then re-assembled it. Total time was less than 30 minutes. Now the problems began. Trying to line up the drum to the bearing plate was very difficult due to the bulk of the drum. After some frustration time I devised a way to do it. I took 3 1/12 inch #10-24 screws and cut the heads off. Then I screwd them into to bearing plate as guide pins. I then backed them out after installing each of the mounting screws. It worked very well. Next as I have large arms and hands Iworked form at least 30 minutes to attached the drive belt to the moto and idler pulley. I finally got it on by attaching the belt first around the motor then pulled the idler arm down to engage it over the belt. Took a lot of positioning my hand correctly to get enough leverage to pull the idler arm down far enough. All in all not to complicated and my wife just won't part with this dryer that really dries clothes quickly.I glad I took on the task to repair it and my hats go off to PartSelect.com for quickly and correctly filg mypart order. Hope you have the same success.

door handle just snaps right in and the lintfilter is a no brainer. thank you very much partselect keep up the good work

I checked the power (OK) and removed the four screws that held the timer/controls (upper panels) cover. This revealed a schematic for the dryer that enabled me to determine the door swich was probably the culprit. I pried out the old switch and, sure enough, it was always open (checked with multi-meter). I found the replacement switch easily using the dryer model number and "door switch" search string. Ordered Sunday night, the part came on Tuesday and took 2 minutes to install (no tools needed).

It was super easy, done in 5 less than 5 min. Thanks Parts Select. Parts Select made it easy to find the replacement part by posting pictures. Thanks

Clips on the inside of the door handle had snapped off, 1 minute later it worked like new. NO TOOLS required! So happy my older appliances can have new life by the parts carried by PartSelect. Thanks!

My husband broke the door handle, but of course, i had to be the one to order the part & fix it. I ordered the part on the weekend and much to my suprise it was on my doorstep on Tuesday when I got home from work. Then I saw the part was shipped from nearby Louisville. I was overly happy with partselect!!!!! All I did was open the packaging and clip the dryer handle into the 4 holes. Easy as pie!!!!

removed top by removing two screw inside door,
found felt was out of place and ruined--found some wear on bearing at rear of drum--decided to
replace these parts plus fround bearing--also
new belt ,since it was apart---to remove the drum
you have to remove front panel,which required
removing two bolts from inside at top--front of
dryer just lays down--then you can pull tub out-
I read other customers repair storys ,which made it real easy.

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

Boyfriend did the repair but it took very little time, the dryer now runs nice and quiet with no thudding and all my clothes are safe from being eaten!

pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

Pull old one out stick new one in. Less than 1 minute. Last repair was the water pump that was easy.

I repaired it by logging on to parts select website and found the part, waited for about a week or so and opened up the box. I glanced at it and found out that wow it's the exact match except new. Unbelievable and in excitement I went to my laundry room and opened up the dryer and popped that baby right in! Thanks Parts Select

I removed the rear panel to access the drive belt. Lowered the pulley to remove the belt and then took off the front panel and popped the top lid off. The belt was slightly frayed on the edges and looked a little old. Inside of the dryer was filled with lint, noticed the vent that sucks the lint from the dryer was almost totally blocked because off caked on lint. Probably from the moisture when we lived in Tx and had it in our garage. Sucked it out with the shop vac and scraped the rest. Removed the whole drum and that's when I noticed the rear drum bearing was totally destroyed and only a piece or two remained. Ordered the drum bearing and drive belt. I was about to put them on when I saw the drum slides were worn pretty thin. So I had to order more drum slides. That's why it took me so long to repair the dryer. If I had the parts already, it would have only taken an hour or so. I was pretty excited that I did it myself, since my husband usually fixes everything around the house. Easier than I thought :o)

Pulled old lint filter frame out and replaced with new one, very simple. works like new.

My son in law installed the new part, I didn't watch him so not sure how he did it, think he removed 6 screws, took the front panel off, installed the new part , took less than 15 minutes, now, dryer working again! Sure saved me money, of course, the dryer might die tomorrow from old age but today, working like a charm.