DLB3400SBLAD Hotpoint Dryer - Instructions

pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

My son in law installed the new part, I didn't watch him so not sure how he did it, think he removed 6 screws, took the front panel off, installed the new part , took less than 15 minutes, now, dryer working again! Sure saved me money, of course, the dryer might die tomorrow from old age but today, working like a charm.

i removed two screws and lifted the top up on it hinges. the heating coil was readily accessible. luckly one of the thrmostats fell apart.
partsselect was great. exploded diagrams let me locate and order the replcement easily.

thanks to partsselect i can keep my 16 year old dryer forever.

Pulled old lint filter frame out and replaced with new one, very simple. works like new.

I repaired it by logging on to parts select website and found the part, waited for about a week or so and opened up the box. I glanced at it and found out that wow it's the exact match except new. Unbelievable and in excitement I went to my laundry room and opened up the dryer and popped that baby right in! Thanks Parts Select

With my hands, a 2 yr old could of done it. But I was amazed how quickly I received the part. Thanks

I removed the rear panel to access the drive belt. Lowered the pulley to remove the belt and then took off the front panel and popped the top lid off. The belt was slightly frayed on the edges and looked a little old. Inside of the dryer was filled with lint, noticed the vent that sucks the lint from the dryer was almost totally blocked because off caked on lint. Probably from the moisture when we lived in Tx and had it in our garage. Sucked it out with the shop vac and scraped the rest. Removed the whole drum and that's when I noticed the rear drum bearing was totally destroyed and only a piece or two remained. Ordered the drum bearing and drive belt. I was about to put them on when I saw the drum slides were worn pretty thin. So I had to order more drum slides. That's why it took me so long to repair the dryer. If I had the parts already, it would have only taken an hour or so. I was pretty excited that I did it myself, since my husband usually fixes everything around the house. Easier than I thought :o)

It was very easy. Pop out old, connect new wires and done! Can't say enough as to how fast and easy getting the part from this company was. Ordered the part later in the day one night and on the second day the part was there. Outstanding service.

First removed the power from the dryer for safety. Removed the back of panel. After testing to see if there was continuity in the heating element and replacing all the thermostats in a previous repair. The switch was the next thing to replace. Removed several screws holding the switch in place then disconnected the cables one at a time and placed onto the new switch. The cables plugs are also unique in the desgin which would enable a person not to mess up if all the wire detached at one time. Then reattached the switch back into the dryer, then attached the back panel.

Easy. Take old one out, put new one in.

first I removed the screws with the nutdriver at the bottom of the dryer at the back..then I could see the belt was broken...next I took off the 2 nuts at the back that hold the top on ..then opened the dryer front door and unscrewd the 4 screws holding the top on....then I lifted the top up and to the side...then all I had to do was take out 2 screws one on each side of dryer front and the the front was open enough that I could slide the new belt on dryer..then screwed the front back on...then placed the top on and went to the back of dryer and put belt on pulley using the diagram I found in the instructions inside the dryer top...really a lot easier than it sounds...easy fix saved me from buying another dryer

Unplugged the machine.
Removed four screws from the top of the machine to uncover the top of the machine.
Pulled the leads off the broken switch.
In the future I will make a note of which lead goes where. There are only two ways.
Went to PartSelect.com and found the part in less than a minute by using their part finder.
Placed the switch through the original opening in the machine and reattached the leads.
Reattached the cover. Plugged the machine back in. Turned the switch and it started right up.

* Please note, if only the starter switch peg is broken you do not need to replace the starter knob if it isn't damaged. The peg is not attached to the starter knob. You must replace the entire starter unit because the peg isn't detachable.

Remove the starter knob by gently pulling it towards you.

Remove the two screws on the bottom left and right sides of the front panel using an Allen Wrench.

On the rear panel of the dryer remove bolts using pliers or an adjustable wrench. Remove the back panel and place it to the side.

** Important ** Before disconnecting the wires from the starter unit take a digital photo (I used my cell phone) of the starter so you will know how and where to reconnect the blue and brown wires to the unit. Now, remove the wires.

Unscrew the bolt attaching the starter unit to the dryer. There's a hook on the back of the starter unit attaching it to the dryer. Push the starter unit downward to remove it from the dryer.

Take the new starter unit out of the box and connect it to the blue and brown wires. Refer to your photo for proper connection.

Insert the starter unit into the dryer and push it upward so the hook on the back of the starter locks onto the dryer. Screw the bolt back onto the starter unit to secure it to the dryer.

Replace the rear dryer panel and tighten all bolts.

Replace and tighten the two screws on the front panel of the dryer.

Replace the starter knob by lining it up with the peg shape and gently pushing it onto the peg.

You're done!!!

I discovered that the High Limit Thermo was in place, but had been bypassed years ago. After lifting the top up, I finally found the HLT on the top left side in the back. I removed it, then put the new one in with its 2 screws. I put new lugs on its wires and put them back on. The dryer tested GOOD. No more potential Bar-B-Que! I did print a picture of the wiring diagrams that were on the back of the unit. This gave me the color code of the wires, where they were to be found, and what they did. This also helped. This GE Dryer is at least 26 years old! Newer Dryers in the Videos actually require more work removing things to get to the Thermostat. When I finally found it, the job went quick.

Easy repair, but did take a little longer than anticipated due to the extra cleaning that I did while the dryer was disassembled (highly recommend). First, unplug the power cord. Then, open the door, and locate the two screws in the upper corners, and remove. This will allow you to remove the top cover. Be careful and work the top panel up and down to loosen the control panel tabs, and set aside top panel. Next, remove the two screws located near the top on the inside of the front panel. Removing these two screws will allow you to lean the front panel forward, lift up, releasing the tabs holding the bottom of the panel. Be careful when you pull the front panel from the dryer as you will need to lift the drum off of the front bearing which is attached to the front panel as it is removed. You will also need to use your needle nose pliers to remove the wires prior to setting the panel aside. The wires are straight forward and power the light at the top, and the safety door switch. I always take a picture with my phone's camera just to validate when I re-connect them. Reaching underneath the drum you will be able to feel the belt and belt tensioner pulley. With both hands under the drum, use one hand to push the pulley to the right, releasing tension on the belt. Move the belt out of the groove, and let it hang freely. Now from the top of the drum, bump the drum to loosen, and remove from the cabinet. It is a tight fit, so you will need to spread the sides slightly in order to remove the drum. Next, remove the 3 screws holding the heat diffuser in the rear of the drum in order to remove the rear drum bearing. (Tip: It would be nice to have a helper hold the new drum bearing in place when starting the screws, and it also helped to tighten each a little at a time to keep the new bearing flat as it was drawn up next to the drum.) Tighten the screws holding the new bearing in place. Next, remove the 4 small screws holding the heating element housing to the rear of the dryer. (Tip: Rather than disconnecting the wires, I used a bent coat hanger to hold the housing while I removed the bearing retainer and clip from the rear of the housing.) Remove the 4 screws holding the bearing retainer and clip, and replace with you new part, paying close attention to the clip's position, and tighten. Replace the housing to the rear of the dryer. (Tip: Now is a good time to familiarize yourself with the belt and tensioner pulley for reassembly. Also, it may be a good idea to look at your belt, and replace as needed.) Next, reinstall the drum and insert the new bearing shaft into the new bearing housing. Using both hands again, reach underneath the drum, locate the tensioner pulley, and belt. Push the tensioner pulley over to the right, and move belt over the pulley on the motor, and behind the tensioner pulley. The belt should be tight. If not, inspect to ensure that the belt is over the motor pulley, and the tensioner pulley. Next step is to reinstall the front panel. I also spent the extra money and replaced the front drum bearing, and slides. Please note that the green slides are on top, and the white slides are on the bottom. Lift the panel over the tabs, lean forward while lifting the tub, resting the tub on the front bearing. Reinstall two screws in the upper corners, and tighten the front panel back in place. Now is a good time to turn the drum to ensure that the belt is in place, and that the drum turns correctly. (Tip: If your dryer is equipped with a light, you may also want to replace the bulb in the front panel (if needed) prior to attaching the front panel.) Reinstall the top panel by aligning the tabs in the control panel with the top panel, being careful not to bend the tabs. Next, open the front door and use the 2 long screws to reattach the top panel to the front panel. Plug in power cord.