Models > DHDSR46EG1WW > Instructions

DHDSR46EG1WW General Electric Dryer - Instructions

All installation instructions for DHDSR46EG1WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DHDSR46EG1WW
76-90 of 794
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Insanely high pitched squeeking of and on

  • Customer: Kristine "the Laundry Quenn" from Frankfort IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
-- Unplug dryer from electrical outlet
-- Open Door
-- Remove two screws going up into the top panel
-- Remove top panel
-- Close door
-- Remove two screws holding front panel
-- Remove Front Panel by turning out, keeping left side close to unit since wires are still connected.
-- Vacuum out all loose dust/lint
-- Tilt old Drum bearing toward you to remove.
-- Remove Old Felt Drum Seal
-- Install drum Slides on new Drum Bearing
-- Install new Drum Bearing, make sure it clicks into place securely.
-- Install new Felt Seal, make sure to push in far enough to securely hook to the clips on the bottom of the Drum Bearing.
-- Reinstall front and top panels
-- Plug in electrical
-- Dry

had a bad switch,would not start

  • Customer: jack from payette ID
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
opened up the control cover, pulled off the 3 wires to the switch. unclipped the swutch from the panel and reinstalled the new exact replacemnt sww you sent

old bearing completley gone; shaft eating through race making a horrible noise when running

  • Customer: greg from abilene TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

Faint Squeek after dryer had been running for an hour or so

  • Customer: Stephanie from Cicero IN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
It makes it real easy if you have two people!! Put the dryer on it back--You'll need to protect the floor and the warm air exhaust of the dryer.
Remove the two screws that secure the top--they are located on the inside upper portion of where the door seats on the front panel. Remove the top
Remove the front by removing two screws near the top--one on each side
Remove the belt from the idler pulley--note how it comes off
Lift drum out of dryer
Use the torx bit to remove the bearing
If you got the kit it comes w/ the bearing housing--you'll need to disconnect a couple of the wiring harnesses holding the heater--replace the bearing housing
This is the perfect time to remove all dust bunnies
Re-install everything in reverse order

Front drum seal and top drum sliders

  • Customer: Harold from Mingo Junction OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
Remove front by removing two screws at top of door opening. Remove front of dryer carefully becsuse of electrical connections for door switch. Drum sliders simply silde in slots at top. (4 are required for total replacement) Door seal simply fits in the groove and locks over end tab. NOTE Do not run dryer any more than absolutelty nessary without lower seal in place.

Dryer was making high pitched screeching noises when running.

  • Customer: Chris from Sherwood AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
I removed the top of the dryer by removing two screws located under the front lip of the dryer over the dryer door. Then I removed the dryer door by removing the screws holding the hinges. I then removed the front panel of the dryer by removing the two screws at the top inside two corners. I the removed the old Dryer Drum Slide. The Drum Bearings were almost completley worn off. I installed the (4) new Drum Bearings (2 Clear or White and 2 brown) the same way they were installed on the old Dryer Drum Slide on the new Dryer Drum Slide. I then installed the Dryer Drum Slide the way I removed the old one. Then I pulled the old Lower Front Drum Seal-Felt and replaced with the new one. Works like new!

Could not adjust the timer sttings

  • Customer: Jeff from Sammamish WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
The inner piece of the knob cracked so it just spun on the dryer shaft it's suppose to turn. Ordered a new knob, slipped it on and all works great again now.

My dryer was especially noisy like a constant squeeking sound.

  • Customer: Mark from Yorkville IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
I had already replaced the four (4) small wear strips which were like short strips of teflon, and the squeaking decreased almost completly. I noticed that front side of the drum itself had started to wear through the actual plastc drum bearing, but I hoped having previously replaced these tefon strips that would be the overall fix.
Wrong again... after a few weeks the squeeking continued until I ordered the new drum bearing and replaced the worn one with the new one. I was able to re-use the previous teflon wer strips, and it's like new now at least the squeaks are gone,

The actual fix was a very simple remove old drum bearing, snap in new drum bearing install old teflon wear strips put four screws in top, and front panel and I was back in business

lint filter was broken

  • Customer: bill from clarendon hills IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
took out broken filter and replaced with new lint
filter.

only orderd two sliders needed four

  • Customer: William from Leesburg IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
easy no problem

Dryer squeeked badly when running.

  • Customer: Craig from Castle Rock CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 8 people found this instruction helpful
I've always heard it was a simple job to replace the belt and that would solve the problem. I'd defer to others online when they suggest to replace the rear bearing - they are totally right about that suggestion. My bearing basically fell apart in my hands. Not sure if I needed a belt or not, but it's worth replacing while you are tearing the thing apart. It took way longer to tear apart than to put back together. The parts and prices from PartsSelect were perfect. The parts were received in 4 business days as they said and were perfect replacement parts.

blub burned out.

  • Customer: Mary from Oak Point TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
I first throwed the breaker then I took the old bulb out. Put new bulb in. Turned the breaker back on.
It worked great

Dryer knob broke

  • Customer: Kelcy from Hammonton NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
Pulled off old knob and snapped new one into place. Took about 5 seconds. Must be a lame design cause my dryer's less than 2 years old and the knob snapped on the inside and wouldn't turn. Easy to fix though.

Blower wheel shaft hole was rounded out, lamp was out

  • Customer: Edwin from Eagar AZ
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 8 of 17 people found this instruction helpful
Removed two screws on dryer top and removed top, removed two screws holding front of cabinet and removed cabinet front to the side, disconnected wires to door switch, removed two bolts from motor mount bracket, pulled motor back to access blower wheel, removed old wheel and installed new one, reversed steps, unscrewed old light bulb and screwed in new one.

Had pure hell getting to drum belt and putting it back onto motor pulley and idler, cussed a little, didn't really help . replaced front of cabinet and top, did test run all worked ok.

This job was a little difficult, espicially accessing the belt and idler pulley...

the dryer knob was broken

  • Customer: barbara from Valrico FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
I went on line to Parts select to price the part and found it had directions to fix it also.I purchased the new timer for my dryer and since I had originally broke the knob I purchased that as well..for under $100. I received the part,took that dryer apart, replaced the broken parts and now have a working dryer. I can feel very proud of myself that I did not have the added expenses of a repair man to go with it. Thanks for your help. Barbara R.
All Instructions for the DHDSR46EG1WW
76-90 of 794