Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS3487203
This part is used to start the dryer once you have selected a setting on the timer. The terminal locations on the new switch may be different, match up terminal numbers from old switch to new.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
Used a screw driver and needle nose pliers to remove clip from behind the timer knob. Took 2 minutes to remove clip, i admit it was a little tricky but once you get a grip on the clip very easily removed. Replaced with new knob, old knob gear was completley stripped . put the new clip on and presto, Like brand new.A normal service call would of ran me 45.00 just to tell me what was wrong with the machine.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Just removed the screws at the top of the control panel cover and flipped it down. The switch was then in plain view and simply slid out ( after taking off knob)..placed wire terminals on new switch as I took them off old switch. Slid new switch back in place to lock it in then put control panel cover back into place and replaced screws. Your good to go.
I took apart the top of the dryer and removed the switch and replaced it with the new one. I also removed the knobs and replaced them. Easy
Unplugged dryer. Removed knobs and display panel. Removed bad start switch. This was a bit tricky for a novice. Had to do a bit of twisting. Once the new part was installed, I screwed in the display panel. The dryer worked, but I discovered that the part wasn't securely in place. It took three tries before I finally figured out how to secure the part. Now, everytime I start my dryer, I sing "I am Woman, Hear me Roar!" Woo Hoo!!! Sounds like a little thing to all you Do-It-Yourselfers out there, but to me, this really empowered me. Hmmm, what's next? Maybe the edge of the garage door??? See Ya!
First I figured out it was the start switch, I heard it make an electrical zap noise when I turned it and then the dryer didn't start. Once I had the part I simply removed the back from the dryer with a screwdriver (5 phillips head screws and 1 flat head). Then I twisted the old switch and it popped right out. Then I unhooked the wires and rehooked them to the new switch. Then I twisted the new switch into place, tested the dryer - IT WORKED! After that I just replaced the back cover and I was done. It was so quick! I am a 25 year old single mother with a 21 month and 4 month old. If I can do it on my own anyone can!
Use snub nose plier took less than fifteen minutes.
Repair was simple. Initially thought the problem was the Water Level pressure swith, but since water overflow was only happening when selecting cold wash & during the rinse cycle (Always cold water) the Dual Valve Selenoid replacement FIXED the problem. Took 5 minutes to replace.
Unscrewed three screws on back and removed the switch and inserted the new one. There are 3 wires that clamp on the switch. Remember to unplug before doing this.Real easy and great people to work with. Much cheaper than a technician repair.Jim
I narrowed the porblem down to the rotary start switch, which is located in the top panel. It takes a hex wrench to remove the four screws holding the fron top panel in place and of course the knobs had to be removed. The switch rotates about a wuarter of a turn to come out. Label and remove the three connectors (3). It took about a week to get the replacement part which was slightly different than the original part. The good thing is it had the three prongs like the old part.. I hooked the connectors in the same configuration as the old switch, plugged the power cord back in to test and it started right up.
Unplug. Remove 3 knobs at front of panel. Remove 4 screws. Panel pulls forward. Remove green grounding wire to allow panel to come forward more. Pry up locking tab on switch. Turn switch to unlock from panel. Install new switch in reverse order of removal. Pull off each wire one at a time from old switch and attach to new switch. Reinstall panel and insert 4 screws. Done. My wife was so suprised that it actually worked and I fixed it in less than a day! Only took about 20 minutes. Thanks Part Select and the other repair stories that I read on your website.
Removed the 6 screws that held the top panel in place. there are only 3 wires, 2 that go together and 1 single wire.Uplug the dryer,twist out the old switch,twist in the new one, attatch the wires,replace the panel,BAM your done.And the best part of it all the part was right the first time.they make it so easy to get the right part the first time!
I moved the dryer away from the wall and unplugged the electrical cord. I unscrewed the 4 screws on the top of the dryer to gain access to the Dryer Rotary Start Switch. I pulled the part out of its set location and carefully removed the clip on wires. I then carefully attached the wires to the exact locations on the new part and put it back into the proper location. I installed the screws, plugged in the power cord and moved the dryer back to its location for operation. I turned the circuit breaker back on. I failed to mention that I turned that off first of all. I set the dryer control to dry and turned the Dryer Rotary Start Switch to on and it worked immediately. This took about 12 minutes totally from start to finish. Thank you for being there. Sincerely, John Pewters
Washer - remove 4 screws (phillips)on the back of the panel, slide it sidways slightly and pull forward to release. remove clip behind knob ( kinda like the clip on old car window handles) remove knob and dial. remove 1 nut on timer, rotate timer to release. installation is just as easy, but put clip onto knob first then just push onto dial shaft, it will click when on correct.Dryer - remove 4 screws (phillips) on back of panel and remove same as washer. dryer switch will have a little cam lock on it just pull it off the plastic retainer and rotate switch. Remove wires one at a time and put on new switch so as not to wire wrong. reverse for re-assembly
The repair would have been extremely easy, if only the part was correct. The original starter switch was discontinued-WE4M402, which had 4 prongs to connect to my dryer's 4 electrical wires. The manufacturer substituted a new part-WE4M519, which has only 3 prongs. PartSelect suggested I contact GE and ask what I should do to properly connect the starter switch. The GE help was totally useless, just repeating that the original part was discontinued and a new substitute part was issued; they could not provide any information as to how to install a switch that previously required 4 electrical wires but now only provides for 3 electrical wires. Of course GE would be happy to schedule a service call and have a repairman come out.
opened up the control cover, pulled off the 3 wires to the switch. unclipped the swutch from the panel and reinstalled the new exact replacemnt sww you sent
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.