Models > D120 > Instructions

D120 - Instructions

All Instructions for the D120
31 - 45 of 148
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Needed new filter
Replace filter
Parts Used:
Grease Filter
  • Vincent from Foxboro, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knobs on stove where wore to the point I could not see the numbers for the temp. easy replacement
Very easy just pulled off old knobs and replace with new ones,
Parts Used:
Selector Knob Thermostat Knob
  • Darla from SULPHUR, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old Jenn-air down draft stove
new knobs...parts hard to come by. Only site who had parts for my model stove. Even they are not fully available. I love my stove and wanted it to good new again. The knobs helped alot. I would love to be able to get more parts, if I could find them.
Parts Used:
Selector Knob Surface Burner Knob Grease Filter
  • Judy from San Diego, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
6 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Parts Used:
Light Bulb - 40W
  • Yafa (and David) from Bothell, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
5 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Oven Handle and Missing Indicator Light
Removed the outer cover from the oven door by taking out approx. 9 screws. Cleaned the inside while I had it off. Attached the new handle with two screws (weren't included) had to use old screws. Then reattached the cover.
Replaced the indicator light by removing approx. 4 screws from the control panel. Slipped the new indicator lens in the hole and slid the light socket into place to hold the lens. Reattached the control panel.
Job Complete!
Parts Used:
Indicator Light Kit Oven Door Handle Assembly
  • Tina from Hernando, MS
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
5 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element failed
Simple plug in.
Parts Used:
Grill Element
  • Andrew from Salem, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element in oven burned out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I had to use a mirror and flashlights to see in the back of the oven to replace the screws in the new element. It was very close quarters and difficult to see behind element plate.
Parts Used:
Bake Element with Screws
  • Eric from Bliss, NY
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Nearly 29 year old grill element was broken and not heating properly.
Unplugged and removed the old grill element by hand and installed the replacement element by plugging it into the socket. Tools were not required for this and it took less than five minutes. The new element is great and heats much better than the original did before it broke.
Parts Used:
Grill Element
  • Robert from Venice, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
nubers worn on thermostat knob
Ordered new one, it came, and I put it on. The hard part was finding the model number,
Parts Used:
Thermostat Knob
  • June from Russellville, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Numbers on surface burner knobs were illegibel.
I also sprayed them 3-times with a clear coat before installing. The clear coat I purchased at WalMart once I noticed it claimed to be safe for plastic. Avoid a clear lacquer based product.
Parts Used:
Surface Burner Knob
  • Wayne from NEENAH, WI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No power to any microwave functions
Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. Reassemble and you are done!
Parts Used:
Ceramic Fuse - 20 amp
  • Richard from CALIFORNIA, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grill elemnt on ancient Jenn-Air died
Just replaced old with new, it plugs in same as old.
Parts Used:
Grill Element
  • John from York, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
time to replace the filter
lift out old filter, wash, put in new filter.
Parts Used:
Grease Filter
  • Karen D from Columbia, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knobs were worn badly
Pulled off old knob, then pressed on the new one.
It was very easy, and the part was the correct one.
Parts Used:
Surface Burner Knob
  • Royce from Garland, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed Replacement Filters
Remove Vent Cover, Remove Old Filter, Replace With New Filter, Replace Vent Cover, Repair Complete
Parts Used:
Grease Filter
  • Grady E from Vidalia, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the D120
31 - 45 of 148
Back to Top