CYG2000AWW Magic Chef Dryer - Instructions

First of all, Parts Select is a great service. By giving us an idea of what parts we needed we were able to buy them without a lot of expense. My son and I did this repair together, and it took us a long time. We found an excellent video for repair on the web, and then lost it and couldn't find it again. We had trouble even getting the dryer opened up. That is where a putty knife comes in handy. Be sure to find out how to open it; it will save you a lot of grief. It is supposed to be easy, but it wasn't. Still,it was great to get it fixed so inexpensively. I'll leave the "how I did it" part up to people who had an easier time, but no regrets that we did it. Parts select sent the parts right away.We ended up only using the coil kit.

flame sensor was a little tricky since a wrench was necessary since there was no clearance buy pretty simple put back plug in started still no heat after 6 min running time . now it coil kit so simple was surprised change out both and put cover back on plug in started and been drying ever since thanks for all your help

TURN OFF POWER TO DRYER............................. Pay attention to where everything is as you take it apart, so it can be put back the same way. Take out the two screws by the lint screen. Use flat tip screwdriver between space in front of top to help lift top. Use rag on tip of screwdriver so as not to scratch it. Take out two screws inside the front panel at the top. One on each side. Unhook the switch wiring. Lift up the front panel to take off. The tub will be loose, so it can be taken out to inspect other components. Some call the tub a drum. Be sure to see how the belt tensioner is attached, so it can be put back on the same way, if it comes loose. It is under the tub. Take out old belt. Put new belt around tub. Make sure the tub sets on the two rollers in the back of dryer. While holding tub, put the belt around the grooved pulley on the motor. Grooves are face down against the tub. Feed belt through the tensioner. Put the bottom of front in on the tabs. Be sure belt is still in place around pulley and tensioner etc. Hold tub through front door and close front. Put the two screws back in on each side. Close top and put the two screws in at the lint screen. Done. Turn power back on. Turn on dryer to see if it operates properly. If not, check out your repair to see if everything is connected properly.

Followed videos seen on the internet for my dryer's repair. Went exactly as shown.

Used PartSelect instructions for routing belt & a customer's valuable guidance.

I removed screws for the lint screen - TOP. Pry up top with screw driver. Disconnected inside top front 2 screws, removed door control wires, white and blue. Lift off front of dryer. Tip dryer back about 40 degrees against wall. Remove warn belt (not broken). Relocate idler bracket on the cabinet base, follow diagram which comes with the belt package. Be very careful that the belt is NOT on the side of the idler roller. I had to do this install a second time, because I had it wrong the first time. Even though I've done this repair 5 or 6 times, there's always a first time GOOF. Not really a hard job.

Threw away the printed instructions and followed the Part Select video ,featuring Steve...

Well my husband did the install and he said it was very easy??

Ordered thermal fuse and cycling thermostat

Just follow the excellent video at Partselect. Be careful placing the new blower wheel if the fit is tight. I chipped a piece off mine while tapping it on, but it still works fine. Excellent help with diagnosis, installation, and prompt service at Partselect. I put their magnetic business card on my refrigerator.

Opened the top, removed the front panel. Supported the drum with my foot while I replaced the coils. I used a very short screwdriver so I would not have to remove the drum.

Watched a you tube video on replacing a dryer belt for a whirlpool dryer. Perfect instructions. Dryer is working great.Thank you

I opened the 5x5" door in the front of the dryer. Unscrewed the clamp holding the two coils down replaced/reconnected the coils and screwed the clamp back down

video on your website made it super easy

Removed the two screws fromt he lint track on the top of the dryer. Inserted putty knife between the top of the fromt panel and the dryer top and pushed in to release the two catches for the front panel. I rested the top panel against the wall to get it out of the way of the front panel . Next I removed the two nuts at the top of the front panel . Removed the electrical safety connector for the door using a very small screwdriver to release the catch. Pull up on the front panel to detach it from the bottom catches. I rested the drum on a couple of 2x4s to support it while the front panel was off. Locate the housing for the coils which is on the front of the dryer left side. Remove the cover fromt he coil housing by using a stubby phillips screwdriver and remove the top two screws. Remove the wiring connectors from each of the coils. Replace the coils being careful to align the coils with the "keys" in the housing cover. Reverse the process to complete the job taking care to ensure the felt around the drum does not bind.