CWEF310GSC Crosley Range - Instructions

First, I read about the experiences of others who did this repair.

Then I removed the oven door by removing the single screw at each hinge - visible when the door is open - using a #2 Phillips screwdriver (the only tool needed for this repair). I placed the door on the kitchen table and removed the two screws at the inside top of the door - they also hold the handle onto the door.

I placed the four screws removed from the inside corners of the door -- into one corner of a tray I used to hold the parts in order. Then I removed the eight screws from the perimeter of the door and placed them into another corner of the holding tray. Then I turned the door over and removed the outside part of the door from the inside - as in removing the cover from a box.

Then I removed four screws holding the middle and outside glass panels and placed them in another corner of the parts tray. Then I removed two screws holding the steel panel against the glass. Then I removed the broken glass from the bottom of the tray. That's when I discovered I had ordered the wrong glass panel.

I called the PartSelect number to return the glass, and while discussing how to return the part, I asked if I had to call another number to get the correct part. The lady assured me she could process my order for the correct part. She was very knowledgable about the system and quickly found the correct part from the schematic. I received the replacement part 24 hours later and installed it within 20 minutes.

Overall a success story. Excellent service and easy work.

Turned off power to appliance removed the screws connecting the element. Disconnected the wires from the old element connected the new element replaced the screws and tightened turned power on turned power back on heated oven to be sure it worked. Very simple to do.

Remove the 2 nuts holding the element in place. Pull the element out slightly to expose the wires. each side of the element has a wire. Slide the wires off. Replace new element. attach wires and pu the 2 screws back in the element holders.

Turned off range/oven breaker. Opened the oven door. Removed two 5/16 hex head screws. Pulled bake element forward and removed the two slip on electrical connections from old bake element and put them on the new one. Replaced the two screws, closed the oven door, and proceeded to overhaul the kitchen faucet.

Take the screws out of the inside of oven for the element and slide the oven away from way and remove the back and insert the element to the clips and screw the back of the oven back together and plug in again and push back in place. Very easy for my husband to repair.

After doing without the oven for a week or so we decided to turn to the internet and try doing the repair ourselves. We are not mechanically inclined/fix it yourself kind of people. This really was easy. Just detach the old element and attached the new one. A couple of bolts and snapping one out and then the new one in. Very simple

All I had to do was loosen the screws, pull out electrical hookup on both ends, hookup new heating element to elecric and screw em into place. That's it, super easy and I got the part in 2 day : )

The problem was caused by the owner placing an aluminum catch pan under the bake element. The failure of the element was where it was in contact with the pan. The repair involved removing two screws pulling out the element to access the wires. The connectors were the pull off type so I just disconnected the wires from the old element and placed them on the new element, pushed the element back in place and replaced the two retaining screws. I suggested that the owner not place anything in contact with the bake element. Be sure to up-plug the stove plug before attempting repair.

It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.

Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!

The simplest repair ever! I just snapped it in and put the drawer back - fixed. I hope I have other repairs this simple.

I had to replace the switch on one of the large elements. It could and should have been a quicker repair if there would have been some installation/wiring instructions included with the part. Other than that the repair went well.

was easy open the back side of the range and change the part, the only issue was the wire I used the diagram

I removed the oven door using a phillips screwdriver. It was very easy because I didn't have to worry about the door hinges springing the door back. I'm not really handy and it went very easy.

Remove drawer. Insert new slide. Install drawer.

Removed the old & simply inserted the new one