CTN1911GEW Magic Chef Refrigerator - Instructions

took off lower bracket, replaced parts, put back together, no more squeek!

Pulled socket out of housing, unplugged it from source, plugged in new socket and replaced the socket into housing, screwed in bulb and it worked!!

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

Just removed old trim and attached new trim by hand. good results. Happy with your product and tmeliness of delivery Thanks Doug Salter

I love how easy it was to find out what part I needed by seeing the photos to verified it was the part I needed. The repair was super easy and the directions were easy to understand. I didn't even need tools.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

All you need is a 1/4" nut driver or a 1/4" socket and ratchet. Remove the plastic cover to the freezer fan. remove cover to light fixture, bulb, pop out the light socket and remover 2 wires. Remove Ice maker by removing bottom screw and loosing the top 2 screws then lift up and out the ice maker enough to disconnect wiring harness. Revove 4 screws in back panel and the panel can be moved foward. Remove 2 screws holding the fan to the panel. Lay the fan on top of the cooling coil and remove ice maker electrical plug and the panel can be removed easely. Both the heating coil and thermostate switch are easly excessable.

Replaced the "Run Capacitor. The non-rythmic clicking associated with the compressor coming on continues. The problem was obviously not the Run Capacitor". I don't know what to do next. Any suggestion would be appreciated.

Thanks,

Phillip

Removed back cover to see motor and the fan. Un plug the fan motor from the fan. Used 1/4in socket to remove 3 screws, then unscrewed plastic mounting plate off of motor, put plate back on new motor, used pliers to remove nut from fan blade,and rubber washer replaced to new motor. Then put new motor back in. Make sure motor is centered back in hole and fan does not hit. The brackets (3) that hold motor in place will swing so it can be centered in hole. Spin blade to make sure blade not hitting and is centered. Now plug fan motor back in. Just that simple.

The main issue is that my supports are NOT held on by screws -- they are behind the fridge wall and can not be removed. So this is my solution (ignore the 'fix kit' -- it is useless and is just this part plus a metal screw. It cost me $20 to find this out). Here is what I did: 1) Cut off the old support with a knife. 2) Get a small toggle bolt (I used 1/8" x 2", < $2 from Home Depot) and thread into new support. 3) Dig around in insulation to make sure there is space for toggle to flip open. 4) Install!!!! Wish I'd thought of this before :-)

The fan motor was burned up affecting the efficiency of the refrigerator. I removed the fan motor, tested it, ordered a new one and installed. saved 100 bucks in service call charge and got great service in delivery from parts direct. Ordered on Thursday and recieved monday.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

removed the back cover unplugged the unit removed the old fan blades installed the new easy to pull off and easy to install

removed old mount with allen wrench replaced with new mount