Models > CTN1911GEW > Instructions

CTN1911GEW Magic Chef Refrigerator - Instructions

All installation instructions for CTN1911GEW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CTN1911GEW
91-105 of 117
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Light bulb failure

  • Customer: Grant from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

one of the fan blades was broke causing it to vibrate

  • Customer: michael from westminster SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed the back cover unplugged the unit removed the old fan blades installed the new easy to pull off and easy to install

broken crisper drawer mount

  • Customer: lloyd from california KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed old mount with allen wrench replaced with new mount

light switch sticking

  • Customer: Paula from Rush NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

Light did not come on (bad bulb!) on TC18KL

  • Customer: Louis from Beloit WI
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

Broken End Cap

  • Customer: michael from Hoffman Estates IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply replaced part. Press fit shelf retaining bar back into place. I was just glad you had this obscure part which was easy to find on you website.

replaced oven lightbulb

  • Customer: peggy ann from forest city NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
very easy

Lower shelf holder kept falling out

  • Customer: James from Williamsport MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed keeper on left side, slid trim into keeper on right, attached left keeper to trim, re-inserted keeper onto door.

rocker switch broke off

  • Customer: STANLEY from OAKLAND NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

broken cap ends

  • Customer: thomas from sonoma CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
put the end caps on

My glass fell and broke

  • Customer: Marsha from Tamarac FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I just reinstalled the glass I received.

control was broken

  • Customer: Mary from Glade Hill VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took the new knob out of the box and popped it in place. The end. EZPZ! quick service and quick repair. Thanks!

freezer was cold but fridge compartment was not

  • Customer: Fred from Concord NH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed fan shroud in center of plastic finish cover in back of freezer by unsnapping. Removed back cover in freezer by removing 4 screws with nut driver. Removed power connection from fan motor and removed 2 screws holding fan motor in place with nut driver. Installed replacement motor following steps in reverse. Plugged in fridge and cooling began with fan running.

Small plastic parts in door broke years ago.

  • Customer: Daniel from Rock Hill SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After thinking it would be impossible to find the parts I needed to fix my old refrigerator I found PartSelect.com. I was surprised that not only did they carry the parts but all were in stock. The actual repair was as easy as the ordering. For the shelf retainer bars and end caps I just put the ends on the bars and snapped it into the door. Care should be taken not to try to bend the end caps too much to insert into the door or they will break at the inside of the bar. They are only thin plastic. I actually bought two spares for future if needed. For the crisper drawer shelf support I used my 1/4" nut driver and removed the piece of the old support with the screw and installed the new one. Do not over tighten the screw or you might a: strip the hole out the sheet metal screw goes in or b: damage the new support or both.

Broken crisper shelf

  • Customer: Henry from Franklin IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
My husband was cleaning shelf. Took to kitchen sink to wash, hit edge & glass shelf broke in a million pieces. We ordered the replacement that night (Wednesday) & received new glass on Friday. Couldn't believe how fast the turnaround was. New glass was installed in seconds & we were good to go. Only without shelf for a day & a half. I now know where to order parts from. Thanks.
All Instructions for the CTN1911GEW
91-105 of 117