CTF16AGCR Hotpoint Refrigerator - Instructions

I ordered the valve, which came only a day later. Mine is really simple because it only has one water line and one electrical plug in. I do not have a separate water filter. First, I unplugged the refrigerator and shut off the water supply. I unscrewed the cardboard piece from the lower part of the back of the fridge and freed the valve. I pulled out the top water tube that goes from the valve to the top of the fridge, that connects into the back of the ice maker. That tube was empty and dry - I blew through it to make sure that it was unobstructed, and it was. No water was getting to that tube at all. I pulled out the plugs from the valve, and unscrewed the water line from the valve and let that drain in the bucket. I had drained as much water in the lines as I could by flushing a toilet and turning on the sink until it seemed the water supply that was left in the pipes was low. Then I just did the reverse putting together everything with the new valve. I screwed back in the water line that runs from the wall to the fridge. I pushed in the water hose line into the valve until it was all the way in. It was uneven and frayed at the end of that thin hose line, so I cut it very straight across the bottom so it would be entirely flush when it was pushed all the way into the valve. Then I inserted the plug back into the new valve. I put everything back in place, plugged in the fridge and turned on the water supply. I had left the fridge out off the wall so I could check for any leaking. I left it overnight and by morning I had ice! It was so easy. My only difficulty was pulling out the thin water hose from the valve. I did not realize that you can push down on the circular rim and the hose just slips out. I think I saved a lot of money.

Replaced single outlet valve for the ice maker

Defrost timer is hidden in the control panel in the refrigerator top middle. Turn to off and remove two screws which are hidden behind white tabs. I had to pry the old timer from the plug with a screw driver because it was tight. Try not to short across the terminals. Plug in the new timer. Replace it in the clip where you got old one and reinstall the controls. The freezer was still all frosted up so I had to remove the cover and defrost it with a hair dryer to get it to work. Then I turned it on and it works great.

took water line loose at outlet valve to confirm that water was getting to valve. I ordered part and it arrived the next day. It was very simple installation took 10 minutes. Thanks to parts select, Kirk

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

take fan out,put new in

Your online instructions were easy to understand and follow. I replaced the outlet valve which took about 20 min. Then I had to dissasemble and remove icemaker to de-ice inlet tube and back wall of frezzer to defrost cooling fins. All to gether it took me about 1hr / 40 min. Frezzer now works just like new. Thanks for making it affordable and easy. Curt

Checked the defroster coil which is located behind the rear panel in the freezer compartment, it was still working. Followed the schematics down to the defrost timer, which is located in the lower front of the refrigerator and tried that. Plugged in the new part and the problem is solved.

Changed out the valve the water line hooks to in back of fridge and bingo that was the problem , less them 10 min job.

removed the inside fridge electrical panel and swapped switches

had to replace copper water line to valve

Hi, My furnace when out when I was away, frozen water lines were repaired, but my ice maker line was turned off, the valve split open. Summer is coming I want ice! I found the right replacement, ordered it, watched the free video, did the repair. It was so easy. And I saved an expensive service call. I am drinking a soda with ice from the ice maker as I type this! Thanks for solving my problem, I will be back next time something needs a part! Bob

1) This is a built-in refrigerator with the compressor, coils, etc. at the top. Turn off the breaker to the fridge. 2) Remove the front panel off the top (just push up and pull out). 3) Removed 2 screws to the old timer and carefully remove the plug. Plug the new timer in and screw in. 4) Since our fridge was heavily frosted up, we moved everything to another refrigerator and coolers and kept the refrigerator off until all panels were room temperature. 5) If you haven't cleaned the coil in a while, vacuum it with a soft brush attachment. 6) Turned back on and the refrigerator is cooler than ever!

easy pry out, disconnect wiring, connect on new switch and press in switch.

Detached the old part from the refrigerator and disconnected the low voltage quick connect. Also disconnected the water line to the Ice Maker. Reinstalled the new part in the order it was disconnected and re attached the water line feed to the valve threaded connection. Turned water on and no problems.