CSM25MRCEWW Hotpoint Refrigerator - Instructions

1. Turn water supply off at wall. Unpulg referigerator. Remove all cardboard backing covering valve. Vaccum under ref. Unscrew water line where it attaches to valve on ref. (Reuse this later) unplug 4 electrical prongs. Mark with colored pen if not already color coded, so can put back correctly. Pull old ice maker and ref water supply out of valve if it does not screw in with nut. Cut very short peice off end of ref water lines. Slide new locks on water supply lines and push into water valve very hard to lock. Cant get them wrong as they are different sizes. Plug in electrical connectors same as you unpluged them. Connect water line to valve from wall. Turn water on and check for leaks. If none. Replace all screws on backing. Recheck for water on floor. If none congrads, just saved yourself about $120. 00 Labor. Take 2 asprin, drink a six pack and go to bed.

Unplug the unit. Remove the food from the freezer. The following three items must be removed to access the panel in the back of the freezer. 1. Remove the shelves below the ice maker. 2. Lift up the plastic shield over the light to remove and then 3. Unscrew the light bulb. Using the 1/4 in nutdriver, remove the two hex screws at the top of the panel. Carefully slide it up and out past the shelf brackets. Below the cooling coils, identify the defrost heater. Using the phillips screwdriver, remove the two screws, one on the left and one on the right. Carefully manipulate the heater to pull down and remove the slip-on electrical connections at either end. Reversing the procedure, install the new defrost heater slipping on each of the electrical connections and then screwing in the two screws. Be sure to position the wires they were originally to avoid interference when reinstalling the panel. Slip the panel in place behind the shelf brackets and align the holes. Insert and tighten the hex screws. Screw in the lightbulb and replace the plastic light cover. Replace the shelves. Return your food and plug the unit back in. Done!

I had to defrost large chunks of ice from the rear of the freezer compartment and tried reactivating the ice maker several times before deciding to order the replacement fill tube grommet and clamp. This was very stressful and complicated to accomplish while trying to avoid food spoilage, and consumed a lot of time. It involved removing the ice maker and various panels, plus disconnection of 2 electrical plugs, then using a hair dryer to melt ice build up. The installation of the new parts was quick and simple once they arrived in the mail, and this appears to have solved the leak problem. The fill tube slides easily into the grommet and the clamp, tightened with a screw driver, secures the water feed line on the other end. Fill tube must be carefully threaded through rear panels and into the ice maker receptacle and the grommet needs to be pushed hard and wiggled in order to seat properly in the rear surface of the refrigerator.

Popped off the front frame and front of mother board. unscrewed the assembly to be able to lift up to get to flapper. Lifted it up out of the the way ( wires are attached so it may take one other person to hold it up out of the way). Pop out the old flapper and replace with new one. Easy !

Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.

Did the repair jut like the instructions on the web site stated. There was a good video for doing this repair. Looked at it a couple of times and did the repair right off the bat. Thanks folks.

Purchased two new drawer slides and installed in less than 5 minutes. 2 screws on each side. Extremely easy

I removed the lower cover plate and placed a small scissor jack (used my car jack) under the refrigerator door, loosened the upper hinge, slightly raised jack to take the weight off of the lower hinge, removed the hinge with a 5/16 nut driver and the cam with a 5/16 socket. Installed new hinge and cam, removed door support and secured top hinge, check operation. Worked GREAT, did not have to remove door.

Remove ice maker bucket. Unscrew single screw in center of shield, take out shield. Insert new shield, making sure the 2 tabs on the shield are slid into mount from the left, center the shield so center tab is aligned with screw hole, Tighten screw, replace ice bucket. SUGGESTION: This would be a good time to replace light bulb!

I am more than 80 yrs, always thought I could fix just about everything--but, this looked complicated. Once I received the new icemaker; took a good look where the screw-holes, etc. were, then removed the "old" one. Took about 20 or 30 minutes, then the "new" one was easily installed.

I removed the ice container with the auger inside. I removed the front panel, then the auger and housing. I had to clean all of the parts that had rust on them. I got some of the parts mixed up and was having a hard time putting them back where they belonged. I went back on the PartSelect web site and with my IPad and opened the exploded view of the parts. This enabled me to put the auger back together. It works perfectly now. Saved a lot of money by doing it myself. Thanks PartSelect.

The Hinge Cam Riser came as ordered and arrived in 1 day! The original riser was clearly broken in half. After installing the new one on the door hinge and adjusting it several times, the door closed a little but still didn't close all the way. Finally, I re-installed all the door trays and filled them with the usual perishables, and the door closed perfectly! Apparently, the extra weigh on the door was needed to complete the job.

parts select delivery time unreal !!!!! ordered on a Tues. was here Wed !!!! Perfect fit, minor difference in tubing connection. Took more time to clean the floor once i moved the fridge than the actual repair. Thank you Parts Select, if i need more appliance repair parts, you're my first choice>

Washed new Ice Bucket assembly with dish soap and warm water, and let dry. Removed (4) small screws holding Ice Bucket Door assemby to my original Ice Bucket assembly. Reinstalled Ice Bucket Door assembly to new Ice Bucket.

I watched the video of the repair, and followed their procedure. First turned off ref. removed trays, removed light and then back panel. located defrost heater at bottom of condensing coils. Removed and replaced. reassembled and ref. works great. Thanks ross