CRE9800DDE Maytag Range - Instructions

Turn off breaker in electric panel fore stove. Put screw driver into slots in front of glass top surface. Pry top up carefully until top pops up.Remove burner dial, remove two philips head screws holding switch. Lift top carefully and prop up.With new switch close remove wires from old switch one at a time and place on new switch. Place new switch back in place, securing with philips screws. Remove prop and carefully press top down until it snappes into place.Replace dial, turn breaker back on and try burner.

First I reviewed a video on YouTube by this site. Even though the range on the video was not the same as mind, it gave me an idea on what to do. I proceeded to pull the rang out from the wall and disconnected the power plug. Next I removed two screws from the back located on the left and used a flat blade screw driver to depress two brackets on the front to release the glass top panel. I unplugged the wiring harness and disconnected the grounding wire and took the glass panel off and laid it upside down on the kitchen table. I removed the old heating element first by unplugging the wiring and removing the brackets that held it in place. Installed the new one, plugged in all wirings, brackets, screws and replace the top back on the stove.

I didn't. Don't know how to get to light bulb to change it for this specific model

Shut off power at breaker box , pull stove away from wall , remove Phillips screws from back of range pull knob off of switch . Look to see how switch is oriented remove 2 screws that hold switch in . Remove one set of wires at a time and place on new switch in same location . Put back together in reverse order .

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.

Took the old levelling leg out and screw the new one in.

The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on the new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.

i removed the two screws that holds the element in. I pulled the element out and disconnected the wires and I had to adapt a double male adapter to the wire ends and plug the wires back onto the element. The old element had male spades and the new element had female spades.

I killed power
Pulled the back panel
Pulled the door off
pulled light socket wires
reached in and bent in light socket tabs
knocked out light socket
slide in new socket
lifted top of stove (glass)
disconnected glass top wiring
pulled off glass top
pulled both side panels
removed both hinges,
installed new hinges
reinstalled side panels
reinstalled glass top,
reinstalled light socket wiring
installed back panel
installed door
restored power

I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just 4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

replaced Hi-Limit button by removing rear oven cover. Changing by removing screws than replacing with new button.................................. changed sensor by removing screws inside oven and replcing with new unit. changed connector behind rear cover.

The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.

Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.