CRE9800DDE Maytag Range - Instructions

shut power off to range. removed oven shelves to make getting old element out a lot easier. removed screws that hold old element to back of oven - carefully pulled old element out about 3-4 inches. pulled power connectors off end of element. then installed new element in reverse order. Very easy to do. My wife could have done,but she does baking. I do the repairing. Thank-you for such great service. Greentown joe

turned breakers off unscrewed two screws, removed old element.Reattached wires on new element,put two screws back in. flipped breakers back on and its good to go.

number 1 was to shut off circuit breaker. Just removed 2 screws pulled out element slowly to expose wire terminals, removed wires carefully so terminal was not damaged. Replace element was spot on so install was in less than 5 min.

customer service was great depart was easy to install and worked like a charm

killed power...removed back of stove...removed switch and replaced it..reinstalled back...powered up

Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)

Turn the power off at the breaker first! then I used a phillip head screwdriver and unscrewed the two screws that was holding the metal plates on, then pulled the element out with the wires connected and pulled off the terminals. Then i put the new element in and hooked the wires to the terminals then pushed back through the back of the oven then screwed the plates back on then it was done!

The "PartsSelect" General discription of the parts funtion helped me to confirm my suspitions that there was some form of temperature registering problem. I whatched the short video they provided on how to change the part out, even though, in this case, it's pretty self explanitory.The part was in my hands a day erlier than promised and in reality, much earlier than I had anticipated from the beginng. It took me all total, 20 minutes to exchange the part out and have the oven in operation again.

The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.

We lifted the glass top, uninstalled the old burner and installed the new burner in it's place. It worked right away - and is still working. No other tricks the new burner was a perfect fit.

At first I was confused on how to repair this, but once I was able to unscrew the large cover to reveal the inside area, it became clear on which part to replace. The screws were a star type, in which I was able to use an old IKEA hex wrench. There is a small plastic tip that unscrews in the center of this part. Once you unscrew that, the part comes right out. This is my second time ordering a part from these guys for this washer. They are awesome!! The part came in 2 days, so happy!!

The video was good but my model had and additional back plate that wasn't mentioned with 6 additional screws to take out and put back in. Other than that the video explained everything including checking the wires, clips. Oven works great now.

I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!

I watched the video, which was very helpful...the temperature sensor was hard to pull through the small opening in the upper back left oven corner. On the back wall of the oven was a large removable circle, so I unscrewed that piece and was able to gain access to the wires attached to the temperature sensor and push it through the small opening. I used one of the new connectors, pushed it back through the small opening, screwed it back onto the oven wall, replaced the circle opening and tried the oven again...unfortunately, there was no improvement in oven temperature! My JennAir wall oven is about 17 years old, and I thought I would try this $30 repair prior to purchasing a new wall oven, but it looks like I will have to do some overtime and buy a new oven. Any other suggestions would be welcome.

Followed video