CGR3742CDW Magic Chef Range - Instructions

New burner and igniter.....actually it was very easy to to fix

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Twisted and lifted off the burner, loosened in a previous repair; removed electrical wires from igniter; undid two screws holding igniter in place; rotated igniter 90 degrees and lifted it out; reversed process with new igniter.3

turned the old burner to the left and lifted it out. unpluged the wires with a screwdriver pluged the wires into the new burner and putit back on the stove and turned it to the right

replaced igniter with screw driver

I followed the instructions on this website. Luckily a friend showed me where the sensor was located and from there, it was a breeze. Removed six screws on the back oven panel, removed two screws inside of the oven, took the old sensor out and put the new sensor in. Voila - works great. I can't tell you how much I appreciate Parts Select and the feedback and help from the customers. I've been out of work for almost two years and when I called my repair guy, he said it could be the computer and that would be expensive. That's when I searched on line and found Parts Select. I would have never even attempted this on my own if it weren't for you and it was so simple. Next time anything goes wrong with an appliance, I'll be contacting you first! Thank you.

in and out in 15 min ,is easy when part fit.

Removed old gasket and replaced with new gasket'

Took my right hand twisted burner off unplug wires pluged them back into new burner and put burner back on done 3 mins tops.

I tried to take it out from the inside as the vidio shows. But it would not come out far enough. I pulled out the stove and removed back sheet metal panel. Unpluged the electric, Unhooked the temp sensor,pulled it out from the oven side. Put the new one through the hole,and rehooked it up. And got to clean up the dust and my missing oatmeal I spilled a while back. Turned it on. Checked it with a spare temp gage. Works so far.

I lifted up the bottom insert of the inside of my oven and then followed the instructions on this site. Originally I purchased the wrong igniter, so I would encourage you to look at yours and make sure you are buying the right part. I am a complete novice. Even with my purchase debacle, my oven was back up and running within 5 days (total cost was $60). Do this even if you are scared of a screwdriver. Just remember to turn off the gas first. Make sure you've turned off the gas by trying to light a burner (if your burners are otherwise working correctly). If it doesn't light, the gas is off and there is nothing to be afraid of. The igniter is far enough away from the gas pipe that I wasn't afraid of breaking it and once I saw how the oven was put together, I wasn't afraid of working on it. And, if you need to return anything, the return policy is awesome.

With Range unplugged. 1) Turn burner counter clockwise, not even an 1/8 of a turn, to unlock burner from cooktop AND remove wires. 2) Remove the two screws (on both sides) to remove the gas distribution bracket. 3) Raise cooktop up a couple inches (since the tubing was broken already) to loosen and remove flared fittings from burners to ignition valves. 4) Once tubing is disconnected, raise cooktop off of range. 5) Flip cooktop over and remove the burner fittings (this distributes the gas to the burner. 6) Installation is reverse of removal. CAUTION, when you place cooktop back on top of the range, be very careful with your new tubing. You don't want to do this again. When installing tubing onto the ignition valves inside the cooktop ONLY lift the cooktop a couple inches, just enough to get the adjustable wrench in there. NOTE: The flared connection of the ignition valves, is angled downward. This is what makes it a tad difficult.

This oven is part of a stand-alone gas (propane) stove. It was purchased and installed in July, 2005. The igniter I ordered from PartSelect arrived as promised. But the connecter on the new igniter did not match the connecter on the old one. I had to either find an igniter with a compatible connecter or splice the old connecter to the new igniter; I chose to splice. Now, I'm not a real handyman, and I'm especially skittish around electricity. But I found two wire connecters (plastic tube-like things with metal interiors). I stripped about a 1/4-inch from all four wires and inserted them into the wire connecters, making sure the igniter was properly placed so the screw holes lined up. Then I used the crimper tool to crimp the wires together. I did a pull test to make sure the wires were secure, replace the now connected wires in their proper place and turned the oven on. It worked! On this particular stove, you'll need a screwdriver to remove the vent cover, exposing the igniter wires. Due to the gas connection in the back of the stove, you can only pull the stove out so far. So, there's not a lot of room to work in the back of this stove; that's why it took a lot longer to complete this job than the wiring inself. I'd say no more than fifteen minutes. Of course, if all the parts are compatible, even less. Good luck!

We received the burners we ordered in timely manner, and it was very easy to install. Just unhook the old burners and drop the new ones in and connect.

Replaced igniter, removed inside bottom cover 2 screws,removed igniter 2 screws & unplugged igniter from back of oven after removing plate with 1 screw. Could not have been any easier took less than 10 minutes. And doing business with PartSelect was great, would recommend and use again any chance I get.