CCE3401B Jenn-Air Cooktop - Instructions

I cut the circuit breaker to the cooktop. I removed the four control knobs from panel. Then I raised the unit out of the granite counter, placing it on top of a sheet of reinforced cardboard that came with the new cooktop's shipping box, covering the hole in the granite counter. Using a 1/4 socket nut-driver, I removed the twelve screws attaching the glass cooktop to the panel. I lifted the broken glass cooktop from the unit, and discarded it in the box the new cook top came in. I carefully lowered the new glass cooktop in position, and replaced the twelve mounting screws. I turned the unit over, and placed half inch foam tape to the bottom edge, around the perimeter of the new cooktop. Then I turned the unit right side up, and lowered it into the granite counter. After replacing the four control knobs, I turned the circuit breaker back on, and tested all four heating elements. The unit was as good as new! The wife was surprised, and very happy when she returned home to find the job complete. Don't tell her that it was really easy, and only took me about fifteen minutes to do the entire job. She thinks I'm incredible, and can fix anything.

turned off power to stove top..lifted unit out unscrewed top and switch had 2 screws re-placed switch and put back together.. make easy $100 plus switch

Turned off power, disconnected wires, cut tape on exhaust fan connection, removed cooktop from counter and removed glass top from assembly, removed screws on switch, switched wires from old switch and installed on new switch, reinstalled everything, restore power and checkout new switch positions. Everything worked.

I removed the glass top and replaced the switch unit successfully. Hardest part was removing the unit from the countertop and bracing the base with a 4x4.

simply took off smooth surface top flipped it upsde down on a towel. unbolted the entire burner assembly. matched connections with the new burner with limit switch. replaced smooth surface top plugged it in. no problems. extremely easy fix no repair charges.

This was a repair project on a Jenn-Air built-in stovetop, which I had trouble finding instructions on how to disassemble. My particular problem was that three of the four burners had no temperature control. They were either on high or off - no such thing as simmer. This is opposite the problem described as a normal indicator of burner control failure. Usually the burner just goes dead. The hardest part of the repair was accessing the metal plate the burner controls are mounted on. First, I flipped the circuit breaker to the stovetop. It will shock the cr@#p out of you if you don't (I have experience from poking around down there without turning the power off). First, I had to remove the two burner inserts. The left one lifted from the top and the right one lifted from the bottom. Don't lift them past about 30 degrees. They are meant to lift up just enough to clear the tray well and then slide out. After removing the burner inserts, I was able to unscrew the eight fasteners holding down the stovetop rim. After removing this, I pulled out the trays underneath the burner inserts and put them aside without unscrewing the ground wires that attach them to the stovetop chassis. After removing the two screws holding on the active burner indicator lights, I was able to pull it up and lay it aside. Then I had to unscrew the two large brackets under the cabinet to loosen up the stovetop chassis so I could lift the front of it up an inch from the cabinet to enable me to unscrew two small metal screws that attach the metal plate holding the burner controls. After removing the two screws holding each burner control to the metal plate, I could unplug each of the five wires from the old controllers and plug them into the new controllers, in turn, before reattaching the new controllers to the metal plate. After repeating this procedure two more times, I reversed the process to reassemble the stovetop and voila, turned on the power and it worked perfectly. The result; a happy wife. For today.

Here is what I did with new switch (part#12002125) and it worked. Connect jumper to P1 and S1. Split the 2 red wires and put new spades on the ends, then put the red wire from left front switch on P2 and the other red wire from the right rear burner on 2. Blue goes to 4. Purple goes to 4A. Black goes to P1. Orange goes to S2.

We lifted the glass top, uninstalled the old burner and installed the new burner in it's place. It worked right away - and is still working. No other tricks the new burner was a perfect fit.

Removed two screws holding cooktop to oven. Unlike the video, the cooktop was not detachable as the wires were hard-wired to the range, so I had to prop the top up with a 6" block of wood and was working upside down. I replaced the element and everything worked just fine.

Thanks to the highest rated user comment and following his instructions the switch exchange was easy. The supplied instructions were of little to no help and confusing. The hardest part was getting to the two side top Phillips screws because the granite counter top was in the way necessitating raising the stove till the screw heads were exposed. Once raised the front cover was easily removed after undoing six screws. The cook top did not need to be removed. Either of the supplied wires would work and only one of the two was needed. The replacement switch performed far better than the original.

Lifted the range top about 2 1/2 inches, removed the ceramic top and replaced the burner. Tested the burner before replacing the top. Everything worked fine.

Unscrewed three screws securing the glass top. Lifted glass top and wedged it open. Took a picture of the current wiring. Removed old burner.Compared male contact points on new and old burner. Plugged new burner in appropriately. Note: The new burner is MUCH hotter than the old one.