CAW2752RQ0 Whirlpool Washer - Instructions

First I removed the softener bin by pulling it up and off, then I removed the plastic seal by pulling it up and out, then I removed the 1/2 inch bolt with a ratchet and extension, then I removed the upper and lower agitator assembly from the machine and seperated the two by putting my feet on the lower agitator to hold it to the floor and pulling the upper agitator fast and firmly.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.

flip machine back remove two spring clamps and hoses remove two spring clamps and water pump save $500.+on a new washer

I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.

Replaced AGITATOR DIRECTIONAL COGS (4) looking instruction video . Replaced CLUTCH LINING KIT following video of this site "WASHER REPAIR-REPLACING THE CLUTCH ASSEMBLY". Replaced SEAL, GEARCASE COVER and NEUTRAL DRIVE ASSEMBLY as follow: 1)CLUTCH Assembly and motor removed, took the GEARCASE on a bench vise to hold in place and the long shaft up side. You can get help from other person to hold secured in place instead a vise.2)Following a youtube video I tested gearcase with a reversible drill using DIRECT DRIVE MOTOR COUPLING PART next To transmission side instead of electrical motor. Drill turning counter clockwise drive the long shaft oscillating (it agitate via agitator cogs). Drill turning clockwise run the exterior sleeved part around shaft (upper side of metal gear inside gearcase and fixed on top to clutch to get washer spin). My experience was didn't rotate so we had to take apart gearcase cover.3)Unscrewed and removed gearcase cover. Cover was sticked by old seal gasket so a screwdriver helped me to remove it.4)Cleaned joint removing old gasket.5)Repeating drill test I realized big nylon gear did'nt rotated and removed uppercut clip with pin pliers with care for not lose the pin. Removed the next washer, the plastic gear and found a plastic part with a tooth broken. This part is with NEUTRAL DRAIN ASSEMBLY so replaced assembly following part instructions. I recommend take pictures in order to reassemling and use ALLEN WRENCH 5/32'' inches.6)Fill up to half of gearcase with 16 ounces (about 1/2 of case) of gear oil supplied by PARTSELECT or automotive gear oil SAE 85w90 or SAE 90.7)Replaced SEAL, GEARCASE COVER. HARD TO REMOVED AND REPLACE! Take care not break!. I had to use a piece of metal tube and a vise.8)Applied automotrice black seal gasket silicone around the cover joint and case.9) Replaced the cover and reversal instruction video.THANKS to this site I get excellent service and Enjoyed with my toy.

Tilt machine on its side,snap off the two retaining straps and remove the pump and sanded the shaft on the electric drive motor to remove rust ,Install new pump and retaining straps and unit now running great.

placed washer on side and installed new pads
and returned washer upright

After uplugging and removing the hoses from the back of the washer, 1 - Removed four screws that secure control panel to top of machine and tilted panel toward front. Disconnected wiring plugs as req'd to gain more access. 2 - Removed the two gold colored clips that secure the top to the lower sheetmetal housing and tilted the lower housing away from the back of the machine. 3 - Removed the shield that is clipped to the back just above the inlet valve assy. 4 - Removed the hose clamp from the valve, disconnected the four wires to the valve (note their position), Removed the single screw that secures the valve assy to the back and removed the valve assy. Installation is reverse of above.

Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and started stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).

pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.

Unplug machine then removed two screws from the back of the control panel so that the panel could be removed from the top of enclosure. I then removed the two spring clips that fastens the enclosure to the back panel of machine. Stand in front of machine and tilt enclosure back towards you, this opens up the machine to get access to the inlet valve. Remove all electrical wires and the water hose at the bottom of the valve. There was only one bolt that attached the valve to the back panel; remove it and replace water inlet valve.

3 online people recommended tilting the machine on the side and replacing the 3 suspension springs. Someone else recommended changing the tub pads. That is the wrong approach. It is actually easier to remove the case than turn the machine on the side. Once you do it once or twice it takes less than 2 minutes and it doesn't distort the suspension. You don't even have to disconnect the hoses. When I originally examined the machine lying on it's side I saw that the tub balance spring was still attached to the tub but the other end had detached. I looked for the place to reattach it. I found a place on the glide plate. Unfortunately this was the wrong place and the machine continued to bang away. When I realized that the spring had to be attached to the lower frame rather than the glide plate (one week of looking). I even wrote to the Repair guru. Once I found my mistake the repair took 5 minutes and no tools other than the phillips screwdriver to take out the 2 screws for the case. I replaced the tub balancing spring for good measure. The machine works great.

Once I finally found the part I needed, the repair was very simple and took only a few minutes. Thanks to the very helpful operator to walk me through the diagram to find the corresponding number for the part. I really appreciate your help!

Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive assembly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.

The repair was fairly simple and while it made the spin operation quieter and and a bit more stable, it still gets out of balance. Disconnected power, shutoff supply lines and disconnected them from the unit.

Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverage with a 2 x 4 to take any residual tension off the springs.

Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors

Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.

If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.

The agitator kit comes with everything you see in the picture plus the Thrust spacer and O ring. Removed the fabric softener container from the top of the agitator. This revealed the sealing cap that covers the bolt. Removed it using the 2 little handles and rocked it back and forth until it came loose. It doesn't take that much force. Now you see the the bolt to remove. You'll need a socket wrench that has a long extension section ( I didn't have one so I put 2 smaller extension on / it works). Once the wrench was securely in place on the bolt, I held onto the bottom section agitator/ fin with one hand and removed the bolt with the other. I pulled up on the unit and both agitator sections came off together. Once out of the machine, I held the bottom section with my feet and pulled up on the upper section to separate them ( pretty easy) . Removed all the old parts to replace and did a complete clean up of the shaft and bottom( mine was 21 years since serviced there). Used agitator grease on the cleaned shaft area and on the Thrust spacer section. I assembled the agiator dog ears part asper instruction and used a needle nose pliers to remove the plastic nubs that are only use for factory installations. Put the assembly into the agitator tube, then onto the lower section. I put that back onto the shaft, wiggling it until it fell into the grooved section. Once everything was in place, I put in the bolt ( didn't get a new one in time, so I used the old one / it works) and tightened it good. I put a new O ring on the protective cap. I greased it a little so it would go back into place easily, it did. Replaced the softener holder and I was done. Works like new.